JVC UX-A70MDR manual Introduction, Precautions

Page 5

Introduction

We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual for future reference.

About This Manual

This manual is organized as follows:

This manual mainly explains playback and editing operations using the remote control, and the other operation such as recording operations using the buttons on the unit.

You can use the buttons both on the remote control and on the main unit for the same operations if they have the same or similar names (or marks), unless mentioned otherwise.

Basic and common information that is the same for many functions is grouped in one place, and is not repeated in each procedure. For instance, we do not repeat the information about turning on/off the unit, setting the volume, changing the sound effects, and others, which are explained in the section “Basic and Common Operations” on pages 10 – 13.

The following marks are used in this manual:

Gives you warning and caution to prevent from damage or risk of fire/electric shock. Furthermore, gives you information which is not good for obtaining the best possible performance from the unit.

Gives you information and hints you had better know.

Power sources

When unplugging the unit from the wall outlet, always pull the plug, not the AC power cord.

DO NOT handle the AC power cord with wet hands.

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

After starting heating in the room

In a damp room

If the unit is brought directly from a cold to a warm place Should this occur, the unit may malfunction. In this case, leave the unit turned on for a few hours until the moisture evaporates, unplug the AC power cord, then plug it in again.

Others

The electronic swing panel may malfunction when you use this unit under the strong light such as the sunlight.

DO NOT expose this unit to the strong light.

Should any metallic object or liquid fall into the unit, unplug the AC power cord and consult your dealer before operating any further.

If you are not going to operate the unit for an extended period of time, unplug the AC power cord from the wall outlet.

Precautions

Installation

Install in a place which is level, dry and neither too hot nor too cold — between 5˚C (41˚F) and 35˚C (95˚F).

Install the unit in a location with adequate ventilation to prevent internal heat buildup in the unit.

Leave sufficient distance between the unit and the TV.

Keep the speakers away from the TV to avoid interference with TV.

DO NOT install the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration.

DO NOT disassemble the unit since there are no user serviceable parts inside.

If anything goes wrong, unplug the AC power cord and consult your dealer.

– 1 –

Image 5
Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Introduction PrecautionsContents Become familiar with the buttons on your unit Location of the ButtonsMain unit Display window Main UnitWhen using the remote control Remote ControlRemote Control Getting Started Connecting AntennasUnpacking FM antennaAM MW/LW antenna Connecting SpeakersTo connect an outdoor AM MW/LW antenna To attach spacersYou can connect the speakers using the speaker cords Connecting Other EquipmentTo connect speakers To connect another component such as a cassette deckTo start the display demonstration manually, press Putting the Batteries into the Remote ControlTo stop and cancel the display demonstration, press Basic and Common Operations AC power cord from the AC outlet Turning On the PowerSelecting the Sources and Starting Play To turn on the unit without playing, pressTo turn down the volume level temporarily Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesTo set the illumination color Setting the Display IlluminationTo create your favorite colors To dim the display illuminationListening to FM and AM MW/LW Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Receiving FM Stations with RDS Tuning in a Preset StationChanging the RDS Information Searching for Programs by PTY Codes PTY SearchSwitching to a Program Type of Your Choice Temporarily More about the EON function Alarm functionTest function Description of the PTY codes Playing Back a CD To stop playback for a moment Basic CD OperationsTo locate a particular point in a track during play To go to another trackTo modify the program To check the program contentsProgram Play Playing at Random Random Play On the remote control onlyRepeating Tracks Repeat Play To skip the current track, press ¢Playing Back an MD On the main unit only Press MD OPEN/CLOSE You can play an MDInsert an MD into the MD loading slot Press MD #To change the information in the main display Basic MD OperationsPrograming the Playing Order of the Tracks Program Play On the remote control only Load an MD Press MD # / 8, then Random play ends when all the tracks are played onceTo skip the playing track, press ¢ Tracks of the loaded MD will play at randomRecording on MD Main unit Remote controlAbout the track marks Before You Start RecordingTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeRecording CD CD Synchronized Recording Recording FM/AM MW/LW BroadcastsTo record a single track during play or pause Press REC Mode to select the recording modePress AUX Start playback on the external equipmentEditing MD Introducing MD Editing Functions Join Function Divide Function+ 1 ? appears in the main display Move FunctionTo divide the joined tracks, see the Divide function Select the track you want to move Press ¢orALL Erase Function Erase FunctionSelect the track you want to erase Press ¢ or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press SET to enter the selected title entry mode Press ¯or ¿to change the title entry modeDisc title entry screen appears when you press Track title entry screen appears when you pressChanging the Title Using the Timers How Recording Timer actually works Setting the ClockUsing Recording Timer To turn on the Recording Timer, press SET Using Daily TimerHow Daily Timer actually works Volume setting appears in the main display Press ¢or 4 repeatedly to adjust the minute Press SETTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer-on time comesHow Sleep Timer actually works Using Sleep TimerTimer Priority Cleaning the unit MaintenanceGeneral Notes Handling CDsAdditional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Scms Serial Copy Management SystemMD is not loaded correctly There is no MD MD MessagesMalfunction has occurred during Specifications TroubleshootingJVC 1100TMMMDWJEM