JVC UX-A70MDR manual Basic CD Operations, To stop playback for a moment, To go to another track

Page 25

Playing Back the Entire CD — Normal Play

You can play a CD.

1 Press CD OPEN/CLOSE 0.

The unit automatically turns on, the electronic swing panel slides upward, then the disc tray comes out.

Electronic swing panel

Disc tray

2 Place a CD correctly on the circle of the disc tray with its label side up.


Good	No good

•When using a CD single (8 cm), place it on the inner circle of the disc tray.

3 Press CD #/ 8.

The disc tray closes, then the electronic swing panel slides downward automatically.

The CD indicators start flashing on the display and CD playback starts from the first track of the CD.

•If you press CD OPEN/CLOSE 0 again, the disc tray and electronic swing panel close, but CD playback does not start.

Track number indicator

TRACK	1	2	3	4	5	6	7	8	9	10	11	12
			MD				CD					Flashing
The current track										Elapsed playing time

Ex. The CD has 12 tracks and the unit is playing the first track.

•All the track numbers light when the currently loaded CD has more than15 tracks.

•When the unit finishes playing a track, its track number goes off from the track number indicator on the display.

CD playback stops after playing back all the tracks of the CD.

To stop during play, press 7.

All the tracks on the CD

TRACK

1

2

3

4

5

6

7

8

9

10

11

12

MDCD

Total track number Total playing time

Ex. The CD playback stops. The CD has 12 tracks.

To remove the disc, press CD OPEN/CLOSE 0.

Basic CD Operations

While playing a CD, you can do the following operations.

To stop playback for a moment

Press CD #/ 8.

The CD indicators light on the display and the elapsed playing time starts flashing in the main display.

To resume playback, press CD #/ 8again.

To locate a particular point in a track during play

Press and hold ¢ or 4.

•¢: Fast-forwards the tracks.

•4: Fast-reverses the tracks.

To go to another track

Press ¢ or 4repeatedly.

•¢: Skips to the beginning of the next or succeeding tracks.

•4: Goes back to the beginning of the current or previous track.

To go to another track directly using the number buttons (on the remote control ONLY)

Pressing the number button(s) allows you to start playing the track number you want.

Ex.: For track number 5, press 5.

For track number 15, press +10, then 5. For track number 20, press +10, then 10.

For track number 32, press +10, +10, +10, then 2.

– 21 –

Image 25

Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Introduction PrecautionsContents Main unit Location of the ButtonsBecome familiar with the buttons on your unit Display window Main UnitRemote Control Remote ControlWhen using the remote control Getting Started Connecting AntennasUnpacking FM antennaAM MW/LW antenna Connecting SpeakersTo connect an outdoor AM MW/LW antenna To attach spacersYou can connect the speakers using the speaker cords Connecting Other EquipmentTo connect speakers To connect another component such as a cassette deckTo stop and cancel the display demonstration, press Putting the Batteries into the Remote ControlTo start the display demonstration manually, press Basic and Common Operations AC power cord from the AC outlet Turning On the PowerSelecting the Sources and Starting Play To turn on the unit without playing, pressTo turn down the volume level temporarily Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesTo set the illumination color Setting the Display IlluminationTo create your favorite colors To dim the display illuminationListening to FM and AM MW/LW Broadcasts Presetting Stations Tuning in a StationTo change the FM reception mode Receiving FM Stations with RDS Tuning in a Preset StationChanging the RDS Information Searching for Programs by PTY Codes PTY SearchSwitching to a Program Type of Your Choice Temporarily Test function Alarm functionMore about the EON function Description of the PTY codes Playing Back a CD To stop playback for a moment Basic CD OperationsTo locate a particular point in a track during play To go to another trackProgram Play To check the program contentsTo modify the program Playing at Random Random Play On the remote control onlyRepeating Tracks Repeat Play To skip the current track, press ¢Playing Back an MD On the main unit only Press MD OPEN/CLOSE You can play an MDInsert an MD into the MD loading slot Press MD #Programing the Playing Order of the Tracks Program Play Basic MD OperationsTo change the information in the main display On the remote control only Load an MD Press MD # / 8, then Random play ends when all the tracks are played onceTo skip the playing track, press ¢ Tracks of the loaded MD will play at randomRecording on MD Main unit Remote controlAbout the track marks Before You Start RecordingTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeRecording CD CD Synchronized Recording Recording FM/AM MW/LW BroadcastsTo record a single track during play or pause Press REC Mode to select the recording modePress AUX Start playback on the external equipmentEditing MD Introducing MD Editing Functions Join Function Divide Function+ 1 ? appears in the main display Move FunctionTo divide the joined tracks, see the Divide function Select the track you want to move Press ¢orALL Erase Function Erase FunctionSelect the track you want to erase Press ¢ or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press SET to enter the selected title entry mode Press ¯or ¿to change the title entry modeDisc title entry screen appears when you press Track title entry screen appears when you pressChanging the Title Using the Timers Using Recording Timer Setting the ClockHow Recording Timer actually works How Daily Timer actually works Using Daily TimerTo turn on the Recording Timer, press SET Volume setting appears in the main display Press ¢or 4 repeatedly to adjust the minute Press SETTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer-on time comesTimer Priority Using Sleep TimerHow Sleep Timer actually works Cleaning the unit MaintenanceGeneral Notes Handling CDsAdditional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Scms Serial Copy Management SystemMalfunction has occurred during MD MessagesMD is not loaded correctly There is no MD Specifications TroubleshootingJVC 1100TMMMDWJEM