JVC RX-1024VBK Using the SEA Modes, Creating Your Own SEA Mode, To recall your own SEA adjustment

Page 30

Using the SEA Modes

Creating Your Own SEA Mode

You can adjust and store your own SEA adjustment into memory (SEA USERMODE).

On the front panel only:

If you do not want to store your adjustment, but rather want to adjust the SEA temporarily, skip step 4 below.

1.Press SEA ADJUST repeatedly until the frequency range (100Hz, 1kHz or 10kHz) you want appears on the display.

SEA ADJUST

S E A FR

VOLUME

100 1k 10k

S E A FR

VOLUME

100 1k 10k

2.Turn MULTI JOG to adjust the SEA level of the selected frequency range, while the indication of the previous step is still on the display.

•Turning it clockwise increases the level.

•Turning it counterclockwise decreases the level.

This FR means this adjustment can be applied to the front speakers only

S E A FR

MULTI JOG

100 1k 10k

3.Repeat step 1 and 2 to adjust other frequency ranges if necessary.

4.Press TUNER/SEA MEMORY, while the indication of the previous step is still on the display.

Your adjustment is stored into the SEA USERMODE.

To recall your own SEA adjustment

See page 26.

To erase a stored adjustment

TUNER/SEA MEMORY

Storing a new adjustment into SEA USERMODE erases the previously stored one.

27

Page 29 Page 31
Image 30
Page 29 Page 31
Contents
RX-1024VBK To Reduce the Risk of Electric Shock Large Small Large Small NoneOFF MID MAX Table of Contents Using the DSP Modes Front Panel Remote Control Parts IdentificationLocations Getting StartedGeneral Handling the receiverFM Antenna Connections Connecting the FM and AM AntennasGetting Started AM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerTo enhance your audio system Audio Components Video Components Connecting Audio/Video ComponentsAnalog connections Audio component connectionsVideo component connections Video componentsConnecting DVD player If your video components have an AV Compu Link terminalDigital connections Digital 1 coaxial ForConnecting the Power Cord Putting Batteries in the Remote ControlBasic Operations From the remote controlTurning the Power On and Off On the front panelTo decrease the volume, press Volume Adjusting the VolumeTo increase the volume, press Volume + Press one of the source selecting buttons directlyFrom the remote control only Basic OperationsOn the front panel only Press Sound Attenuating the Input SignalAdjusting the Subwoofer Output Level Recording a SourceSelecting the DBS tuner as the source Basic SettingsSelecting the Input Mode Changing the Source NameListening at Low Volume Loudness Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information YESSetting the Speakers for the DSP Modes Basic SettingsDigital Input Digital in Terminal Setting Front, Center, and Rear Speaker SettingCenter Delay Time Setting Rear Delay Time SettingCrossover Frequency Setting COMP. OFF Low Frequency Effect Attenuator SettingDynamic Range Compression Setting COMP. MIDTo cancel the One Touch Operation function To store the sound settingsTo recall the sound settings One Touch Operation To store the preset stations Tuning in Stations Manually Using Preset Tuning Receiving Radio BroadcastsAuto To erase a stored preset stationSelecting the FM Reception Mode MonoAssigning Names to Preset Stations Receiving Radio BroadcastsTo erase the input characters Using the SEA Modes Selecting Your Favorite SEA ModeTo cancel the SEA mode To recall your own SEA adjustment Using the SEA ModesCreating Your Own SEA Mode To erase a stored adjustmentOn the DAP mode Using the DSP ModesOn the 3D-PHONIC mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes Adjust the speaker output levels as follows To cancel the DAP modePress Surround Mode repeatedly until the mode you Want appears on the displayUsing the Dolby Digital and Dolby Pro Logic Modes Press Surround Mode repeatedly until PRO LogicOr Dolby Digital appears on the display Press Surround Mode repeatedly until OFF appears Adjusted levels are also shown on the equalizer displayTo cancel the Surround mode Press Test to start checking the speaker output balanceTurn Multi JOG to select the center tone level you want Press Dolby Surround so that the lamp on the buttonLights up Press Dolby Surround again so that Surround OFF appearsKeys are activated for sound adjustments Using the Theater Surround ModePress Surround Mode repeatedly until Theater Or DIG-THEATER appears on the displayTo cancel the Theater Surround mode Press Test again to stop the test tonePress Cntr Tone to select the center tone level you want DSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Selecting the Source to Play Also see Using the On-Screen MenusWhen you select OSD, see Selecting the Different Sources for Picture and SoundAttenuating the Input Signal Also see Adjusting the Front Speaker Output Balance Also seeListening at Low Volume Loudness Also see Sound Control menu appears on the TVFor 3D-PHONIC modes Using the On-Screen MenusAdjusting the Subwoofer Output Level Also see For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Digital Selecting Your Favorite SEA Mode Also seeFor Dolby Surround Pro Logic For Theater Surround and Digital Theater SurroundCreating Your Own SEA Mode Also see Basic SettingsPress SET to store the setting into the SEA Usermode Storing the Preset Stations Also see Operating the TunerAssigning Names to the Preset Stations Also see Character entry screen appearsAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingDisc Search Only for CD Player Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Additional FunctionsOperations Showing the Disc Information on the TV ScreenSearch a disc by its performer Text Compu Link Remote Control SystemSearching a Disc Only for the CD player Search a disc by its disc titlePress on Screen Control %/ Þ to move to GENRE, then press Going back to the Disc Title Search screen Press ExitSearch a disc by its genre SETUsing your own User Files Going back to the User File screen Press ExitTitle Input Performer screen appears on the TV Entering the Disc InformationFor the CD Player with the disc memory function To move to Shift , then press SETFor the MD recorder Enter the disc title, referring to steps 3 and 4 onEnter the song title, referring to steps 3 and 4 on Connect to the terminal indicated AV Compu Link Remote Control SystemCables with the monaural mini-plugs not supplied Illustration Do not connect to the TV terminalOne-Touch Video Play Automatic Selection of TV’s Input ModeAutomatic Power On/Off Standby One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Pause RECREW REW Play Down Tuning REC TV/VIDEO Stop Pause Operating Other Manufactures’ Components Following buttons can be used for operating the TVChannel + Set the remote control mode selector to CatvOperating Other Manufactures’ Components 10, 0, 100++10Try to operate your VCR by pressing VCR1 Power Starts playbackPauses Manufacturers’ codes for TV Manufacturers’ codes for Catv converters STS Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 0598OFMMDWJEM
Top Page Image Contents