JVC RX-1024VBK manual Rew

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK jacks (see page 56) in addition to the connections using cables with RCA pin plugs (see pages 9 to 10) or using a digital cable (see page 11).

•When using the remote control:

–For the DVD player and the VCR: Aim the remote control directly at the

remote sensor on the each component.

–For the TV having AV COMPU LINK terminal “RECEIVER/AMP”: Aim the remote control directly at the remote sensor on the receiver when operating the

TV.

–For the TV having AV COMPU LINK terminal “AV COMPU LINK EX”: Aim the remote control directly at the remote sensor on the TV when operating the

TV.

VCR1 (the VCR connected to the VCR1 jacks)

TV/CATV/	VCR 1	AUDIO
DBS

Notes:

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR” ):

VCR1 POWER: Turns on or off the VCR1.

After pressing VCR1 or VCR1 CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations on the VCR:

PLAY:	Starts playing.
REW:	Rewinds a tape.
FF:	Fast winds a tape.
STOP:	Stops operations.
PAUSE:	Pauses playing or recording temporarily. To
REC ¦:	release it, press the PLAY button.
	Press this button with the PLAY button to
	start recording.
	Press this button with the PAUSE button to
	enter recording pause.
CHANNEL +/–:Changes the channels on the VCR.
1 – 9, 0:	Selects the channels on the VCR.
	For channel 5, press 5.
	For channel 10, press 1, then 0.

DVD player

After pressing DVD (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations on a DVD player:

PLAY: Starts playing.

4: Returns to the beginning of the current (or previous) track.

¢: Skips to the beginning of the next track.

STOP: Stops playing.

PAUSE: Stops playing temporarily. To release it, press the PLAY button.

POWER	POWER				POWER
DVD	VCR 1		VCR 2		VIDEO
CD	TAPE/MD		PHONO		TV/DBS
AM	FM				SLEEP
SURROUND	CNTR TONE		–	CNTR		+
MODE	1		2			3	MENU
DIGITAL/	TEST		–	REAR · L		+
ANALOG
INPUT	4		5	ENTER		6
	EFFECT		–	REAR · R +
SOUND	7/P		8			9
	SEA MODE		– SUBWOOFER +
DISC	10		0			+10
	RETURN	FM MODE/				100+
			MUTE		AUDIO/
–	CHANNEL		+		TV/VCR
					CATV
					DBS
MUTE	–	VOLUME				+
ON SCREEN CONTROL
		MENU
SET						EXIT
VCR1					TAPE
	CONTROL
/REW		PLAY			FF/
DOWN	TUNING				UP
	REC
TV/VIDEO			STOP		PAUSE

LIGHT

RM-SR1024U REMOTE CONTROL

•Some JVC VCRs can accept two types of the control signals – code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR1 is set to code “A.”

•You can use either the VCR1 button or the VCR1 CONTROL button to activate the buttons listed to the left. If you press VCR1, the playing source also changes. On the other hand, if you press VCR1 CONTROL, the playing source does not change.

After pressing DVD (with the remote control mode selector set to the “AUDIO/TV/VCR” position), these buttons can be used for the DVD menu operations.

	–	CNTR	+
	2		3 MENU
TEST	–	REAR · L	+
4	5	ENTER	6
	–	REAR · R +
	8

Note:

For detailed menu operations, refer to the instructions supplied with the discs or the DVD player.

60