JVC RX-1024VBK manual Press Test again to stop the test tone, To cancel the Theater Surround mode

Page 41

5. Adjust the speaker output levels as follows:

 

CNTR

+

 

 

 

2

 

3

 

 

MENU

• To adjust the center speaker level, press CNTR +/–.

 

 

 

 

 

 

 

 

 

 

• To adjust the left rear speaker level, press REAR•L +/–.

 

 

 

 

 

 

 

• To adjust the right rear speaker level, press REAR•R +/–.

REAR · L

+

REAR · R +

5

 

ENTER

6

8

9

 

6. Press TEST again to stop the test tone.

TEST

4

 

7. Press CNTR TONE to select the center tone level you want.

CNTR TONE

The center tone adjustment affects the mid-frequency

1

range, which the human voice is mostly made up of.

 

Each time you press the button, the display changes to

 

show the following:

 

SOFT2 SOFT1 FLAT SHARP1 SHARP2

Adjusted levels are also shown on the equalizer display.

This CNTR means this adjustment can be applied to the center speaker only.

S E A

 

 

CNTR (Example: When “FLAT” is selected.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes:

You can adjust the speaker output levels and center tone without outputting the test tone.

You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 19).

You cannot adjust the rear speaker levels when “REAR SPK” is set to “NONE” (see page 19).

Note:

The center tone cannot be adjusted when “CENTER SPK” is set to “NONE” (see page 19).

100 1k 10k

To make the dialogue clearer, select “SHARP1” (little) or “SHARP2” (much). To make the dialogue softer, select “SOFT1” (little) or “SOFT2” (much). When “FLAT” is selected, no adjustment is applied.

8. Press EFFECT to select the effect level.

EFFECT

Each time you press the button, the effect level changes

7/P

as follows:

 

 

 

 

DSP EFFECT 1

 

DSP EFFECT 2

 

DSP EFFECT 3

 

 

 

 

DSP EFFECT 5

DSP EFFECT 4

 

As the number increases, the surround effect becomes stronger.

To cancel the Theater Surround mode

Press SURROUND MODE repeatedly until “OFF” appears.

The DSP and THEATER indicators goes off.

Note:

You cannot adjust the effect level when “REAR SPK” is set to “NONE” (see page 19).

38

Image 41
Contents RX-1024VBK To Reduce the Risk of Electric Shock OFF MID MAX Large SmallLarge Small None Table of Contents Using the DSP Modes Parts Identification Front Panel Remote ControlGeneral Getting StartedLocations Handling the receiverGetting Started Connecting the FM and AM AntennasFM Antenna Connections AM Antenna ConnectionsConnecting the Speakers Connecting the front speakersTo enhance your audio system Connecting the rear and center speakersConnecting the subwoofer speaker Analog connections Connecting Audio/Video ComponentsAudio Components Video Components Audio component connectionsVideo components Video component connectionsIf your video components have an AV Compu Link terminal Connecting DVD playerDigital 1 coaxial For Digital connectionsPutting Batteries in the Remote Control Connecting the Power CordTurning the Power On and Off From the remote controlBasic Operations On the front panelTo increase the volume, press Volume + Adjusting the VolumeTo decrease the volume, press Volume Press one of the source selecting buttons directlyOn the front panel only From the remote control onlyBasic Operations Adjusting the Subwoofer Output Level Attenuating the Input SignalPress Sound Recording a SourceSelecting the Input Mode Basic SettingsSelecting the DBS tuner as the source Changing the Source NameSetting the Subwoofer Information Adjusting the Front Speaker Output BalanceListening at Low Volume Loudness YESDigital Input Digital in Terminal Setting Basic SettingsSetting the Speakers for the DSP Modes Front, Center, and Rear Speaker SettingCrossover Frequency Setting Center Delay Time SettingRear Delay Time Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingCOMP. OFF COMP. MIDTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationUsing Preset Tuning Tuning in Stations ManuallyTo store the preset stations Receiving Radio BroadcastsSelecting the FM Reception Mode To erase a stored preset stationAuto MonoTo erase the input characters Assigning Names to Preset StationsReceiving Radio Broadcasts To cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustmentOn the 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround modeUsing the 3D-PHONIC Modes Using the DSP ModesAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modePress Effect to select the effect level You want appears on the displayUsing the DAP Modes Press Surround Mode repeatedly until the mode you To cancel the DAP modeAdjust the speaker output levels as follows Want appears on the displayOr Dolby Digital appears on the display Using the Dolby Digital and Dolby Pro Logic ModesPress Surround Mode repeatedly until PRO Logic To cancel the Surround mode Adjusted levels are also shown on the equalizer displayPress Surround Mode repeatedly until OFF appears Press Test to start checking the speaker output balanceLights up Press Dolby Surround so that the lamp on the buttonTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsPress Surround Mode repeatedly until Theater Using the Theater Surround ModeKeys are activated for sound adjustments Or DIG-THEATER appears on the displayPress Cntr Tone to select the center tone level you want To cancel the Theater Surround modePress Test again to stop the test tone DSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 When you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundListening at Low Volume Loudness Also see Adjusting the Front Speaker Output Balance Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVAdjusting the Subwoofer Output Level Also see Using the On-Screen MenusFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Surround Pro Logic Selecting Your Favorite SEA Mode Also seeFor Dolby Digital For Theater Surround and Digital Theater SurroundPress SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeBasic Settings Operating the Tuner Storing the Preset Stations Also seeCharacter entry screen appears Assigning Names to the Preset Stations Also seeRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemDisc Search Only for CD Player Additional FunctionsShowing the Disc Information on the TV Screen OperationsSearching a Disc Only for the CD player Text Compu Link Remote Control SystemSearch a disc by its performer Search a disc by its disc titleSearch a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þ to move to GENRE, then press SETGoing back to the User File screen Press Exit Using your own User FilesFor the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the song title, referring to steps 3 and 4 on For the MD recorderEnter the disc title, referring to steps 3 and 4 on Cables with the monaural mini-plugs not supplied AV Compu Link Remote Control SystemConnect to the terminal indicated Illustration Do not connect to the TV terminalAutomatic Power On/Off Standby Automatic Selection of TV’s Input ModeOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Pause REC Operating JVC’s Audio/Video ComponentsREW REW Play Down Tuning REC TV/VIDEO Stop Pause Following buttons can be used for operating the TV Operating Other Manufactures’ ComponentsOperating Other Manufactures’ Components Set the remote control mode selector to CatvChannel + 10, 0, 100++10Pauses Try to operate your VCR by pressing VCR1 PowerStarts playback Manufacturers’ codes for TV Manufacturers’ codes for Catv converters STS Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 0598OFMMDWJEM

RX-1024VBK specifications

The JVC RX-1024VBK is a sophisticated AV receiver designed to enhance the home entertainment experience. This multi-channel receiver is crafted to meet the demands of audio enthusiasts and casual listeners alike, delivering impressive sound quality and a variety of features that make it a standout option in its class.

One of the main features of the RX-1024VBK is its 5.1 channel surround sound capability. This means it can support up to five speakers and one subwoofer, allowing users to immerse themselves in a rich and dynamic audio environment. With a power output of 100 watts per channel, the receiver can fill a medium to large room with high-quality sound without distortion.

The RX-1024VBK incorporates advanced audio technologies such as Dolby Digital, DTS, and Virtual Surround. These surround sound formats provide an authentic cinematic experience by recreating the depth and clarity of audio found in movie theaters. Additionally, the receiver features a robust equalizer that allows users to customize audio settings to perfectly match their speaker configuration and personal preferences.

Connectivity is another strength of the JVC RX-1024VBK. It includes multiple HDMI inputs for connecting various devices like Blu-ray players, gaming consoles, and streaming devices. This functionality allows for convenient switching between sources, ensuring that users can enjoy their favorite content without hassle. The HDMI inputs also support 4K pass-through, enabling high-resolution video output and future-proofing the system for upcoming content.

The receiver also features built-in FM/AM radio with a preset capability, allowing users to save their favorite stations for easy access. An integrated USB port allows for direct playback of media files from USB drives, while line-in connections make it easy to connect older devices.

One notable feature is its sleek design, which fits well into any home audio setup. The user interface is intuitive, making navigation easy for all users.

Overall, the JVC RX-1024VBK combines performance, versatility, and aesthetic appeal, making it a solid choice for those looking to enhance their home entertainment system. With its blend of powerful audio technologies and user-friendly features, the RX-1024VBK is well-equipped to deliver an exceptional listening experience.