JVC RX-1024VBK manual To cancel the DAP mode, Press Surround Mode repeatedly until the mode you

Page 36

Using the DSP Modes

4.Adjust the effect level.

1)Press BALANCE/SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display.

2)Turn MULTI JOG to select the effect level, while the indication of the previous step is still on the display. As you turn it, the effect level changes as follows:

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5

DSP EFFECT 4

As the number increases, the selected DAP mode becomes stronger.

To cancel the DAP mode

Turn MULTI JOG until “DSP OFF” appears in step 2. The DSP indicator goes off from the display.

BALANCE/SURROUND

ADJUST

MULTI JOG

Note:

Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.

From the remote control:

SURROUND

1. Press SURROUND MODE repeatedly until the mode you

MODE

 

want appears on the display.

 

The DSP indicator also lights up on the display.

Each time you press the button, the DSP modes change as follows (the indicator of the selected DSP mode also lights up on the display):

PRO LOGIC THEATER LIVE CLUB DANCE CLUB HALL

OFF

PAVILION

3D THEATER 3D DRAMA 3D ACTION HEADPHONE

When the digital input is selected to play the source encoded with Dolby

Digital:

DOLBY DIGITAL DIG-THEATER

OFF 3D DIGITAL HEADPHONE

If you need to make any adjustment, go to the following steps.

2. Press SOUND.

SOUND

10 keys are activated for sound adjustments.

3. Adjust the speaker output levels as follows:

–

REAR · L +

–

REAR · R +

5

 

ENTER 6

8

9

 

•To adjust the left rear speaker level, press REAR•L +/–.

•To adjust the right rear speaker level, press REAR•R +/–.

4.Press EFFECT to select the effect level.

Each time you press the button, the effect level changes as

EFFECT

follows:

 

 

 

7/P

 

 

 

 

DSP EFFECT 1

 

DSP EFFECT 2

 

DSP EFFECT 3

 

 

 

 

DSP EFFECT 5

DSP EFFECT 4

 

As the number increases, the selected DAP mode becomes stronger.

To cancel the DAP mode

Press SURROUND MODE repeatedly until “OFF” appears.

The DSP indicator goes off from the display.

Note:

The DAP mode is not used with the other DSP modes such as the 3D-PHONIC mode and the Surround mode. When the DAP mode is turned on, the other DSP mode, if used, will be turned off.

Note:

When you select “HEADPHONE,” you cannot go to the following steps. No adjustments can be made for “HEADPHONE.”

Note:

You cannot adjust the rear speaker levels when “REAR SPK” is set to “NONE” (see page 19).

Note:

Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.

33

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
RX-1024VBK To Reduce the Risk of Electric Shock Large Small Large Small NoneOFF MID MAX Table of Contents Using the DSP Modes Front Panel Remote Control Parts IdentificationGetting Started GeneralLocations Handling the receiverConnecting the FM and AM Antennas Getting StartedFM Antenna Connections AM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerTo enhance your audio system Connecting Audio/Video Components Analog connectionsAudio Components Video Components Audio component connectionsVideo component connections Video componentsConnecting DVD player If your video components have an AV Compu Link terminalDigital connections Digital 1 coaxial ForConnecting the Power Cord Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and OffBasic Operations On the front panelAdjusting the Volume To increase the volume, press Volume +To decrease the volume, press Volume Press one of the source selecting buttons directlyFrom the remote control only Basic OperationsOn the front panel only Attenuating the Input Signal Adjusting the Subwoofer Output LevelPress Sound Recording a SourceBasic Settings Selecting the Input ModeSelecting the DBS tuner as the source Changing the Source NameAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationListening at Low Volume Loudness YESBasic Settings Digital Input Digital in Terminal SettingSetting the Speakers for the DSP Modes Front, Center, and Rear Speaker SettingCenter Delay Time Setting Rear Delay Time SettingCrossover Frequency Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingCOMP. OFF COMP. MIDTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Using Preset TuningTo store the preset stations Receiving Radio BroadcastsTo erase a stored preset station Selecting the FM Reception ModeAuto MonoAssigning Names to Preset Stations Receiving Radio BroadcastsTo erase the input characters Using the SEA Modes Selecting Your Favorite SEA ModeTo cancel the SEA mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On the 3D-PHONIC modeOn the DAP mode On Surround mode Using the DSP Modes Using the 3D-PHONIC ModesTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes To cancel the DAP mode Press Surround Mode repeatedly until the mode youAdjust the speaker output levels as follows Want appears on the displayUsing the Dolby Digital and Dolby Pro Logic Modes Press Surround Mode repeatedly until PRO LogicOr Dolby Digital appears on the display Adjusted levels are also shown on the equalizer display To cancel the Surround modePress Surround Mode repeatedly until OFF appears Press Test to start checking the speaker output balancePress Dolby Surround so that the lamp on the button Lights upTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode Press Surround Mode repeatedly until TheaterKeys are activated for sound adjustments Or DIG-THEATER appears on the displayTo cancel the Theater Surround mode Press Test again to stop the test tonePress Cntr Tone to select the center tone level you want DSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Using the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVUsing the On-Screen Menus Adjusting the Subwoofer Output Level Also seeFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionSelecting Your Favorite SEA Mode Also see For Dolby Surround Pro LogicFor Dolby Digital For Theater Surround and Digital Theater SurroundCreating Your Own SEA Mode Also see Basic SettingsPress SET to store the setting into the SEA Usermode Storing the Preset Stations Also see Operating the TunerAssigning Names to the Preset Stations Also see Character entry screen appearsCompu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System Displaying the Disc Information on the TV screenDisc Search Only for CD Player Additional FunctionsOperations Showing the Disc Information on the TV ScreenText Compu Link Remote Control System Searching a Disc Only for the CD playerSearch a disc by its performer Search a disc by its disc titleGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þ to move to GENRE, then press SETUsing your own User Files Going back to the User File screen Press ExitEntering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETFor the MD recorder Enter the disc title, referring to steps 3 and 4 onEnter the song title, referring to steps 3 and 4 on AV Compu Link Remote Control System Cables with the monaural mini-plugs not suppliedConnect to the terminal indicated Illustration Do not connect to the TV terminalAutomatic Selection of TV’s Input Mode Automatic Power On/Off StandbyOne-Touch Video Play One-Touch DVD PlayOperating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Pause RECREW REW Play Down Tuning REC TV/VIDEO Stop Pause Operating Other Manufactures’ Components Following buttons can be used for operating the TVSet the remote control mode selector to Catv Operating Other Manufactures’ ComponentsChannel + 10, 0, 100++10Try to operate your VCR by pressing VCR1 Power Starts playbackPauses Manufacturers’ codes for TV Manufacturers’ codes for Catv converters STS Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierFM tuner IHF HOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 0598OFMMDWJEM
Top Page Image Contents