Multiquip P33/24 HHMR Refuelling, Maintenance work, Parking on uphill and downhill slopes

Page 17

Safety regulations:

3.7.7 Parking on uphill and downhill slopes

Safeguard the machine against rolling away. To do this use metal chocks in front of and behind the drums.

3.8Refuelling

Never breathe in fuel fumes.

Only refuel when the engine is switched off.

Never refuel in enclosed areas.

No naked fl ames, no smoking.

Do not spill fuel, mop up any splashes of fuel, do not allow to seep into the ground.

3.9Maintenance work

Maintenance work may only be performed by suitably qualifi ed and trained personnel.

Keep unauthorised persons away from the machine.

Never carry out maintenance work on a moving machine or with the engine running.

Wherever possible, park the machine on a fi rm and even surface.

Remove the key from the ignition switch.

3.9.1 Work on hydraulic lines

Before performing any work on hydraulic systems, they must be depressurised. Hydraulic oil emerging under pressure can penetrate the skin and cause serious injury. In case of injury due to oil emerging at high pressure, immediately consult a doctor as serious infections can result. When performing adjustment work on the hydraulic system, do not stand in front of or behind the drums. Do not adjust the pressure relief valves.

Drain off the hydraulic oil at operating temperature – danger of scalding! Collect drained hydraulic oil and dispose of in an environmentally responsible manner. Never attempt to start the engine when the hydraulic oil has been drained. After the completion of all work (with the system still depressurised!), check the seal of all connections and

screw joints.

3.9.2 Changing hydraulic hoses

Hose lines must never be swapped or exchanged. Subject hydraulic hose lines to regular visual inspections. The immediate exchange of hydraulic hose lines is essential in the following cases:

Damage of the outer ply through to the inlay (e.g. abrasion, cuts).

Brittleness of the outer ply (crack formation in the hose material).

Deformation in pressureless or pressurised condition which does not correspond with the original shape of the hydraulic hose line.

Deformation on bending, e.g. crushing points, kinks, separation of plies, formation of blisters.

Incorrectly executed installation.

Migration of the hydraulic hose from the fi tting.

Corrosion of the fi tting which impairs functional characteristics and strength.

Damage or deformation of the fi tting which impairs functional characteristics, strength or the hose to hose connection.

Only original RAMMAX spare hydraulic hose lines offer the security of using the correct hose type (pressure stage) in the right situation.

17

Image 17
Contents Vibratory Trench Roller P33/24 Hhmr Page Foreword 12345 Table of Contents Jump start device Loading and transport Maintenance Operation with remote control850 mm 1200 mm 630 mm 1520 mm 500 mm 855 mm 1780 mm RW 1504 /HF/HK/FK/HFK Main dimensionsSteering Rammax RW Noise and vibration specificationsModifications to the machine DescriptionFields of application Safety regulations Operation of the machine Intended useStarting the machine Safety signs attached to the machineLoading the machine for transport Driving the machine Refuelling Maintenance workParking on uphill and downhill slopes Work on hydraulic linesRepairs Cockpit Transmitter Display and operating elementsÖK Oil pressure warning light Description of the display and operating elementsSZ Hourmeter Address setting Back-up safety barEngine safety support Precommissioning checks Operation with remote controlOperation Zone BStarting the engine Driving with vibration Switching on and reversing the direction of travelDriving at high speed Manual control Switching off the machineStarting process Travel operationVibration Loading and transport Jump start device FSERunning in regulations MaintenanceGeneral remarks on maintenance and maintenance work Every day Maintenance scheduleChecking the fuel level Check engine oil levelChecking the hydraulic oil level Changing the fuel filter BatteryChanging the transmission oil Checking / cleaning / replacing the air filter12.1Hydraulic system Changing the engine oilHydraulic oil change High-pressure line filter Changing the suction filter Adjusting the stripperBolt size Tightening torques Nm Tightening torques for bolts with standard metric threadTroubleshooting table Heres HOW to GET Help