JVC RX-6100VBK manual Connecting the Speakers, English, AM Antenna Connections

Page 6
AM Antenna Connections

English

AM Antenna Connections

ANTENNA

Snap the tabs on the loop flame

into the slots of the base to

FM 75

assemble the AM loop.

COAXIAL

 

 

 

 

Basic connecting procedure

1

2

3

 

 

 

AM

LOOP AM Loop Antenna

AM

EXT

123

Outdoor single vinyl-covered wire (not supplied)

Turn the loop antenna until you have the best reception.

Notes:

Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.

If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)

Connecting the Speakers

You can connect the following speakers:

Two pairs of front speakers to produce normal stereo sound.

One pair of rear speakers to enjoy the surround effect.

One center speaker to produce more effective surround effect (to emphasize human voices).

One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 12.

For each speaker (except for a subwoofer), connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Open the terminal and then insert the speaker signal cable.

3Close the terminal.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).

Right speaker

 

FRONT SPEAKERS 1

 

Left speaker

 

 

FRONT SPEAKERS

RIGHTLEFT

1

1

2

2

Right speaker

 

FRONT SPEAKERS 2

 

Left speaker

 

 

Connecting the rear and center speakers

Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.

 

 

CENTER

 

 

 

SPEAKER

 

Center speaker

RIGHT

LEFT

 

 

Left rear

Right rear

 

REAR

speaker

speaker

 

 

SPEAKERS

4

Image 6
Contents RX-6100VBK POWERPOWER AUDIO/VIDEO CONTROL RECEIVERWarnings, Cautions and Others Caution --POWER switchAttention --Commutateur POWER For Canada/pour le CanadaBasic Settings Table of ContentsEnglish Using the DSP ModesParts Identification EnglishChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersEnglish Connecting Audio/Video ComponentsConnecting the subwoofer speaker CD playerTV and/or DBS tuner Video component connectionsEnglish outputEnglish Connecting the Power CordPutting Batteries in the Remote Control Digital connectionsFrom the remote control Turning the Power On and Off StandbyBasic Operations From the remote controlAdjusting the Volume Selecting the Front SpeakersMuting the Sound From the remote controlAdjusting the Tone Adjusting the Subwoofer Output LevelAttenuating the Input Signal Reinforcing the BassRecording a Source Basic SettingsAdjusting the Front Speaker Output Balance Changing the Source NameSetting the Speakers for the DSP Modes 1. Press SETTING repeatedly untilEnglish 1. Press SETTING repeatedly until English1. Press SETTING repeatedly until Digital Input DIGITAL IN Terminal SettingSelecting the Analog or Digital Input Mode EnglishAdjustments - One Touch Operation Setting the Subwoofer InformationStoring the Basic Settings and Using the Sleep TimerReceiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning EnglishEnglish Press MULTI CURSOR %/ Þ3D-PHONICmodes Using the DSP ModesEnglish DAP modesSurround modes EnglishHEAD PHONE mode Dolby Surround Dolby Digital and Dolby Pro LogicBy pressing DSP MODE EnglishAvailable DSP modes By pressing SURROUND MODEFrom the remote control Adjusting the 3D-PHONICModesAdjusting the DAP Modes and HEAD PHONE mode EnglishAdjusting the Surround Modes English1. Press SURROUND MODE 4.Adjust the speaker output levels EnglishDSP EFFECT EnglishDSP EFFECT DSP EFFECTActivating the DSP Modes English1. Press SURROUND so that the COMPU LINK Remote Control System EnglishCONNECTIONS AV COMPU LINK Remote Control SystemEnglish CONNECTIONSEnglish S-videoplugSound control section Amplifier Operating JVC’s Audio/Video ComponentsEnglish TurntableCassette deck EnglishCD player-changer MD recorder3.Enter manufacturer’s code two digits using Operating Other Manufacturers’ Video Equipment1.Press and hold TV POWER 2.Press TV SOUND/DBS 4. Release TV POWER1.Press and hold VCR POWER 2.Press VCR EnglishSOLUTION TroubleshootingPROBLEM English40 Hz to 20 kHz with no more than 0.8% total SpecificationsEnglish harmonic distortionAM tuner EnglishFM tuner IHF GeneralEN, FR J C 0200HIMMDWJEINVICTOR COMPANY OF JAPAN, LIMITED