JVC RX-6100VBK manual English, Adjust the speaker output levels

Page 25
4.Adjust the speaker output levels.

4.Adjust the speaker output levels.

•To adjust the center speaker level, press CNTR –/+ (from –10 dB to +10 dB).

•To adjust the left rear speaker level, press REAR•L –/+ (from –10 dB to +10 dB).

•To adjust the right rear speaker level, press REAR•R –/+ (from –10 dB to +10 dB).

CNTR

3 4

REAR•L

5 6

ENTER

REAR•R

JVC Theater Surround adjustments

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 12).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

•You cannot adjust the rear speaker output levels when you have set “REAR SPK” to “NONE.” See page 12.

•You cannot adjust the center speaker output level and center tone when you have set “CENTER SPK” to “NONE.” See page 12.

English

7/P 8

5. Press TEST again to stop the test

TEST

tone.

0

On the front panel:

You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Press SURROUND to activete an

SURROUND

appropriate Surround mode —

 

PRO LOGIC, DOLBY DIGITAL

 

From the remote control:

1.Press SURROUND MODE repeatedly until “THEATER” appears on the display.

•The Ù PRO LOGIC and DSP indicators also light up on the display.

2.Press SOUND.

The 10 keys are activated for sound adjustments.

3. Press TEST to check the speaker output balance.

“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:

SURROUND

MODE

SOUND

TEST

0

or DTS SURROUND.

•Each time you press the button, the Surround mode turns on and off alternately.

•When “PRO LOGIC” is selected, the Ù PRO LOGIC indicator lights up on the display.

 

TEST TONE L

 

TEST TONE C

 

TEST TONE R

 

 

(Left front speaker)

 

(Center speaker)

 

(Right front speaker)

 

 

TEST TONE LS

 

TEST TONE RS

 

 

(Left rear speaker)

 

(Right rear speaker)

 

 

Notes:

2.Adjust the speaker output levels.

1)Press ADJUST repeatedly until one of the following indications appears on the display.

“CENTER LEVEL”:

To adjust the center speaker level. “REAR L LEVEL”:

To adjust the left rear speaker level. “REAR R LEVEL”:

To adjust the right rear speaker level.

•Once you have pressed ADJUST, MULTI CURSOR %/ Þcan be also used for selecting the speaker.

2)Press MULTI CURSOR @/ # to adjust the selected speaker output level (from –10 dB to +10 dB).

3)Repeat 1) and 2) to adjust the other speaker output levels.

ADJUST

MULTI CURSOR

•You can adjust the speaker output levels without outputting the test tone.

•No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 12).

•No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 12).

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents POWER POWERRX-6100VBK AUDIO/VIDEO CONTROL RECEIVERAttention --Commutateur POWER Caution --POWER switchWarnings, Cautions and Others For Canada/pour le CanadaEnglish Table of ContentsBasic Settings Using the DSP ModesEnglish Parts IdentificationConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Getting StartedBasic connecting procedure Connecting the SpeakersConnecting the front speakers Connecting the rear and center speakersConnecting the subwoofer speaker Connecting Audio/Video ComponentsEnglish CD playerEnglish Video component connectionsTV and/or DBS tuner outputPutting Batteries in the Remote Control Connecting the Power CordEnglish Digital connectionsBasic Operations Turning the Power On and Off StandbyFrom the remote control From the remote controlMuting the Sound Selecting the Front SpeakersAdjusting the Volume From the remote controlAttenuating the Input Signal Adjusting the Subwoofer Output LevelAdjusting the Tone Reinforcing the BassAdjusting the Front Speaker Output Balance Basic SettingsRecording a Source Changing the Source Name1. Press SETTING repeatedly until Setting the Speakers for the DSP ModesEnglish English 1. Press SETTING repeatedly untilSelecting the Analog or Digital Input Mode Digital Input DIGITAL IN Terminal Setting1. Press SETTING repeatedly until EnglishStoring the Basic Settings and Setting the Subwoofer InformationAdjustments - One Touch Operation Using the Sleep TimerUsing Preset Tuning Tuning in Stations ManuallyReceiving Radio Broadcasts EnglishPress MULTI CURSOR %/ Þ EnglishEnglish Using the DSP Modes3D-PHONICmodes DAP modesHEAD PHONE mode EnglishSurround modes Dolby Surround Dolby Digital and Dolby Pro LogicAvailable DSP modes EnglishBy pressing DSP MODE By pressing SURROUND MODEAdjusting the DAP Modes and HEAD PHONE mode Adjusting the 3D-PHONICModesFrom the remote control EnglishEnglish Adjusting the Surround Modes1. Press SURROUND MODE English 4.Adjust the speaker output levelsDSP EFFECT EnglishDSP EFFECT DSP EFFECTEnglish Activating the DSP Modes1. Press SURROUND so that the English COMPU LINK Remote Control SystemEnglish AV COMPU LINK Remote Control SystemCONNECTIONS CONNECTIONSS-videoplug EnglishEnglish Operating JVC’s Audio/Video ComponentsSound control section Amplifier TurntableCD player-changer EnglishCassette deck MD recorder1.Press and hold TV POWER 2.Press TV SOUND/DBS Operating Other Manufacturers’ Video Equipment3.Enter manufacturer’s code two digits using 4. Release TV POWEREnglish 1.Press and hold VCR POWER 2.Press VCRPROBLEM TroubleshootingSOLUTION EnglishEnglish Specifications40 Hz to 20 kHz with no more than 0.8% total harmonic distortionFM tuner IHF EnglishAM tuner GeneralJ C 0200HIMMDWJEIN EN, FRVICTOR COMPANY OF JAPAN, LIMITED
Top Page Image Contents