Weider 831.159290 user manual Following Tools not Included are Required for Assembly, Locknuts

Page 5

ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

•Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.

•Assembly is divided into four stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly and 4) seat and backrest assembly. The hardware for each stage is packaged separately.

•Wait until you begin each assembly stage to open the parts bag labeled for that assembly stage.

•For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual. Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

•As you assemble this product, be sure that all parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) phillips screwdriver

• One (1) rubber mallet

•Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

FRAME ASSEMBLY

1.Before beginning assembly, be sure that you have read and understand the infor- mation in the box above.

Locate and open the parts bags labeled “FRAME ASSEMBLY—METAL” and

“FRAME ASSEMBLY—PLASTIC.”

Press three 2” Square Outer Caps (58) onto the Weight Base (14) in the indicated loca- tions.

Insert four 5/16” x 2 1/2” Carriage Bolts (49) up through the Press Base (13). Insert four 5/16” x 2 1/2” Carriage Bolts up through the Weight Base (14). Insert a 3/8” x 4” Carriage Bolt (57) up through the Weight Base.

Attach the Press Base (13) to the Weight Base (14) with two 5/16” x 2 3/4” Bolts (55), two 5/16” Washers (20) and two 5/16” Nylon Locknuts (40). Fully tighten the Nylon

Locknuts.

1

 

 

 

58

58

 

55

 

 

13

14

20

 

 

 

 

49

40

 

 

 

57

49

 

 

58

49

 

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL Patent Pending Model No Serial NoFull 90 DAY Warranty Table of ContentsImportant Precautions Before YOU Begin DimensionsFollowing Tools not Included are Required for Assembly AssemblyFrame ASSEMBLY-PLASTIC LocknutsDo not fully tighten the Nylon Locknuts Nylon LocknutsLocknut 40. Do not overtighten the Nylon Grooves are on the indicated side of each Stack of WeightsFully tighten the Nylon Locknuts Weight Tubes are in the pin grooves in the upper Weights Nylon Locknuts yet ARM Assembly ARM Assembly ARM Assembly Positioned to hold the Cable in the groove Pulley Find the Butterfly Cable 85-this isTrap must be oriented as shown and be End with Two holes Should be Down Cable Assembly Post Wide Tabs Must be On this Side Cable Assembly Cable Assembly Cable must be routed from the direction shown Find the Press Cable 88. Attach the end Cable Trap is turned to hold the Cable Place Plates 31. The Cable must be routed fromLocknut until step Seat Assembly Cable Assembly Seat AssemblySeat Assembly High Pulley Changing the Weight Setting HOW to USE the Home GYM SystemAttaching the AB Strap to the AB Pulley Station Adjusting the LEG LeverAdjusting the LEG Press Plate Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceButterfly Cable Left Arm Right Arm Cable DiagramsPress Cable High Cable Long U Bracket Leg Press-13 Page Page X 3 1/4 Bolt Qty Description Part LIST-Model NoR0499A Exploded DRAWING-Model NoQUESTIONS?
Top Page Image Contents