KitchenAid YKEHS01P manual Level Dryer, Connect Vent, Reverse Door Swing, Remove the door

Page 16

Level Dryer

Check the levelness of the dryer. Check levelness first side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

NOTE: It might be necessary to level the dryer again after it has been moved into its final position.

Connect Vent

1.Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.

2.Move dryer into final position. Do not crush or kink vent. Make sure dryer is level.

3.(On gas models) Check to be sure there are no kinks in the flexible gas line.

Reverse Door Swing

You can change your door swing from a right-side opening to a left-side opening, if desired.

Remove the door

1.Open the dryer door. Remove the 4 screws that hold the door hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (second from the top).

A

 

B

C

A.Dryer

B.Do not remove

C.Dryer door

2.Lift and pull forward on the door so that the keyhole clears the screw head. Remove the door.

3.Lay the dryer door on a flat, protected surface with the inside door assembly facing up. Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.

4.Remove the 6 screws to release the outer door assembly from the inner door assembly (see illustration). It is important that you remove only the 6 indicated screws.

5.Lift the inner door assembly off of the outer door assembly. Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly aside.

Reverse the hinge and hinge bracket

1.Place the inner door, screw head side up, on the work surface.

2.Remove the 4 screws that hold the hinge to the door.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents FRONT-LOADING Electric Dryer Table of Contents ÍndiceSécurité DE LA Sécheuse Instructions Dinstallation Table DES MatièresDryer Safety Your safety and the safety of others are very importantInstallation Instructions Toolsand PartsOptions Location RequirementsInstallation clearances Dryer DimensionsCustom undercounter installation Dryer only Closet installation Dryer onlyElectricalRequirements- U.S.A. Only If connecting by direct wire Electrical Requirements -Canada OnlyDirect Wire Power Supply CordElectrical Connection -U.S.A. Only Wire connection Power supply cord DEGWire connection Direct wire BDE CG F Optional 3-wire connection VentingRequirementsPlan Vent System InstallLeveling Legs InstallVent SystemAngled hood style shown following is acceptable Level Dryer Connect VentReverse Door Swing Remove the doorComplete Installation Reinstalling the doorClose the door and check that it latches securely If the dryer will not start, check the followingStartingYour Dryer Dryer USETo use an Automatic Cycle Pausingor Restarting Stopping Your DryerControlLocked LoadingStatusLights CyclesAdditional Features Cycle End Signal DryingRackDryer Care Troubleshooting Changing the Drum LightU.S.A Assistance or ServiceCanada Kitchenaid Dryer Warranty KitchenAid will not pay forSeguridad DE LA Secadora Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación Herramientas ypiezasOpciones Requisitosde ubicaciónEspacios para la instalación Dimensiones de la secadoraInstalación en un clóset Sólo para la secadora Requisitoseléctricos- EE. UU Espacio mínimo para la instalación en un armarioLas instalaciones en casas rodantes necesitan Usted es responsable deSi el contacto de pared luce como éste Si emplea un cable de suministro eléctricoSi hace la conexión con cableado directo Cable de suministro eléctrico Conexión eléctrica Sólo en EE. UUCableado directo Conexión de 4 hilos Cordón de suministro de corriente Conectar conSaque el tornillo central del bloque terminal Una caja deConexión de 3 hilos Cordón de suministro eléctrico Conexión de 4 hilos Cable directoConexión de 3 hilos Cable directo Conexión opcional de 3 hilosPlanificación del sistema de ventilación Requisitosde ventilaciónInstalaciones típicas de escape Instalaciones alternas para espacios limitados Instalaciones opcionales de escapeCálculo de la longitud del ducto de escape Instalación delsistema de ventilación Instalación de las patas niveladorasNivelación de la secadora Conexión del ducto de escapeCómo invertir elcierre de la puerta Cómo quitar la puertaComplete la instalación Cómo volver a instalar la puertaCierre la puerta y fíjese que se cierre con seguridad Lea Uso de la secadoraUSO DE LA Secadora Puesta en marcha de la secadoraPara usar un ciclo Automático Dirija el selector hacia un ciclo AutomáticoDetención de la marcha de la secadora Pausa o reanudación de la marchaControlbloqueado CómocargarLuces de estado CiclosCaracterísticasadicionales Alarma de Fin de Ciclo Cycle End Signal Estante de secadoSólo aire Air Only Cuando use Sólo aireCuidado DE LA Secadora Limpieza dellugar donde está la secadoraLimpieza del filtro de pelusa Limpieza de cada cargaLimpieza del interior de la secadora Eliminación de pelusa acumuladaCuidado para las vacaciones y la mudanza Cambiode la luz del tamborSolución DE Problemas La ropa no se está secando bienSonidos raros Pelusa en la ropaAyuda O Servicio Técnico Garantía DE LA Secadora Kitchenaid KitchenAid no pagará porSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteEmplacement d’installation Instructions DinstallationOutillage etpiècesnécessaires Dimensions de la sécheuse Espacements dinstallationInstallation dans un placard Sécheuse seulement Linstallation dans une maison mobile exige Spécifications électriques Canada seulement’est à l’utilisateur qu’incombe la responsabilité de Ne pas utiliser de cordon de rallongeExigencesconcernantl’évacuation Instructions DE Liaison À LA TerreInstallations typiques d’évacuation Installations d’évacuation facultativesAutres installations où le dégagement est réduit Planification du système dévacuationDétermination de la longueur du conduit Installation du conduit d’évacuationLe clapet incliné illustré ci-dessous est acceptable Installation despiedsde nivellement Mise à niveau de la sécheuseConduitd’évacuation Inversion de louverture de la porteRéinstallation de la porte Inverser la charnière et son supportFermer la porte et vérifier qu’elle s’enclenche solidement Achever l’installationSi la sécheuse ne démarre pas, vérifier ce qui suit Mise en marche de la sécheuse Utilisation DE LA SécheuseUtilisation dun programme automatique Verrouillage descommandes Arrêt de la sécheuseArrêt ou remise en marche ChargementConseilspour le séchage et les programmes Témoins lumineuxProgrammes Caractéristiques supplémentaires Grille de séchage Nettoyage de lemplacement de la sécheuse Entretien DE LA SécheuseNettoyage du filtre à charpie Nettoyage à chaque chargeRetraitde la charpie accumulée Nettoyage de l’intérieur de la sécheuseChangementde l’ampoule d’éclairage Du tambour Dépannage Assistance OU Service Garantie DE LA Sécheuse Kitchenaid KitchenAid Canada ne paiera pas pour8557328A All rights reserved

YKEHS01P, KEHS01P specifications

The KitchenAid KEHS01P and YKEHS01P stand mixers are emblematic of KitchenAid's commitment to quality, durability, and innovative design in kitchen appliances. These stand mixers have become essential tools for both amateur home bakers and professional chefs, bringing versatility and performance to every kitchen.

One of the most notable features of the KEHS01P and YKEHS01P is their powerful motor. With a robust engine that delivers reliable torque, these mixers can handle a wide range of tasks, from whipping egg whites to kneading thick bread dough. This level of power ensures that users can mix even the heaviest of ingredients effortlessly.

Both models come equipped with the signature 10-speed slide control, which allows for precise adjustments to suit different mixing techniques and recipes. Whether it’s a slow stir, a moderate mix, or a fast whip, the seamless transition between speeds provides optimal control over the mixing process. This feature is especially beneficial when dealing with delicate ingredients that require a gentle touch.

The tilt-head design of the KEHS01P and YKEHS01P makes it easy to access the mixing bowl and change attachments, allowing for quick ingredient additions and simple cleaning. The mixers are compatible with a wide range of accessories and attachments that expand their functionality, from pasta makers to food grinders, enhancing their versatility in the kitchen.

Another key characteristic of these stand mixers is their sturdy construction. Made with a durable metal housing, the stand mixers provide stability during use and ensure long-lasting performance. Their compact yet powerful design means they can easily fit into any kitchen countertop without sacrificing functionality.

The mixing bowl included with these models is typically a generous 4.5-quart capacity, perfect for preparing large batches of dough or batter. The stainless-steel bowl is not only easy to clean but is also designed to resist rust and wear over time, adding to the longevity of the product.

In addition to functionality, style is not overlooked. KitchenAid offers a variety of colors and finishes, allowing users to find a model that fits their kitchen aesthetic.

Overall, the KitchenAid KEHS01P and YKEHS01P models embody a blend of power, precision, and style. They are designed to inspire culinary creativity while making the baking and cooking experience enjoyable and efficient. With their impressive features and reliable performance, these stand mixers are truly a worthy investment for anyone who loves to cook or bake.
Top Page Image Contents