KitchenAid YKEHS01P manual Electrical Requirements -Canada Only, If connecting by direct wire

Page 8

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

■Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

■10-gauge solid copper wire (do not use aluminum).

■At least 5 ft (1.52 m) long.

■To supply the required 4 wire, single phase, 115/230-volt, 60-Hz., AC-only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

■This dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be sure wall receptacle is within reach of dryer’s final location.

GROUNDING INSTRUCTIONS

■For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

■For a permanently connected dryer:

This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electrical Requirements -Canada Only

WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility

■To contact a qualified electrical installer.

■To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1-latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA.

4-wire receptacle 14-30R

■Do not use an extension cord.

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 9831317. For further information, please reference the service numbers located in the “Assistance or Service” section on this manual.

GROUNDING INSTRUCTIONS

■For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents FRONT-LOADING Electric Dryer Table of Contents ÍndiceSécurité DE LA Sécheuse Instructions Dinstallation Table DES MatièresDryer Safety Your safety and the safety of others are very importantInstallation Instructions Toolsand PartsOptions Location RequirementsInstallation clearances Dryer DimensionsCustom undercounter installation Dryer only Closet installation Dryer onlyElectricalRequirements- U.S.A. Only If connecting by direct wire Electrical Requirements -Canada OnlyElectrical Connection -U.S.A. Only Power Supply CordDirect Wire Wire connection Power supply cord DEGWire connection Direct wire BDE CG F Optional 3-wire connection VentingRequirementsPlan Vent System Angled hood style shown following is acceptable InstallVent SystemInstallLeveling Legs Level Dryer Connect VentReverse Door Swing Remove the doorComplete Installation Reinstalling the doorClose the door and check that it latches securely If the dryer will not start, check the followingTo use an Automatic Cycle Dryer USEStartingYour Dryer Pausingor Restarting Stopping Your DryerControlLocked LoadingStatusLights CyclesAdditional Features Cycle End Signal DryingRackDryer Care Troubleshooting Changing the Drum LightCanada Assistance or ServiceU.S.A Kitchenaid Dryer Warranty KitchenAid will not pay forSeguridad DE LA Secadora Su seguridad y la seguridad de los demás es muy importanteInstrucciones DE Instalación Herramientas ypiezasOpciones Requisitosde ubicaciónInstalación en un clóset Sólo para la secadora Dimensiones de la secadoraEspacios para la instalación Requisitoseléctricos- EE. UU Espacio mínimo para la instalación en un armarioLas instalaciones en casas rodantes necesitan Usted es responsable deSi hace la conexión con cableado directo Si emplea un cable de suministro eléctricoSi el contacto de pared luce como éste Cableado directo Conexión eléctrica Sólo en EE. UUCable de suministro eléctrico Conexión de 4 hilos Cordón de suministro de corriente Conectar conSaque el tornillo central del bloque terminal Una caja deConexión de 3 hilos Cordón de suministro eléctrico Conexión de 4 hilos Cable directoConexión de 3 hilos Cable directo Conexión opcional de 3 hilosInstalaciones típicas de escape Requisitosde ventilaciónPlanificación del sistema de ventilación Cálculo de la longitud del ducto de escape Instalaciones opcionales de escapeInstalaciones alternas para espacios limitados Instalación delsistema de ventilación Instalación de las patas niveladorasNivelación de la secadora Conexión del ducto de escapeCómo invertir elcierre de la puerta Cómo quitar la puertaComplete la instalación Cómo volver a instalar la puertaCierre la puerta y fíjese que se cierre con seguridad Lea Uso de la secadoraUSO DE LA Secadora Puesta en marcha de la secadoraPara usar un ciclo Automático Dirija el selector hacia un ciclo AutomáticoDetención de la marcha de la secadora Pausa o reanudación de la marchaControlbloqueado CómocargarLuces de estado CiclosCaracterísticasadicionales Alarma de Fin de Ciclo Cycle End Signal Estante de secadoSólo aire Air Only Cuando use Sólo aireCuidado DE LA Secadora Limpieza dellugar donde está la secadoraLimpieza del filtro de pelusa Limpieza de cada cargaLimpieza del interior de la secadora Eliminación de pelusa acumuladaCuidado para las vacaciones y la mudanza Cambiode la luz del tamborSolución DE Problemas La ropa no se está secando bienSonidos raros Pelusa en la ropaAyuda O Servicio Técnico Garantía DE LA Secadora Kitchenaid KitchenAid no pagará porSécurité DE LA Sécheuse Votre sécurité et celle des autres est très importanteOutillage etpiècesnécessaires Instructions DinstallationEmplacement d’installation Installation dans un placard Sécheuse seulement Espacements dinstallationDimensions de la sécheuse Linstallation dans une maison mobile exige Spécifications électriques Canada seulement’est à l’utilisateur qu’incombe la responsabilité de Ne pas utiliser de cordon de rallongeExigencesconcernantl’évacuation Instructions DE Liaison À LA TerreInstallations typiques d’évacuation Installations d’évacuation facultativesAutres installations où le dégagement est réduit Planification du système dévacuationLe clapet incliné illustré ci-dessous est acceptable Installation du conduit d’évacuationDétermination de la longueur du conduit Installation despiedsde nivellement Mise à niveau de la sécheuseConduitd’évacuation Inversion de louverture de la porteRéinstallation de la porte Inverser la charnière et son supportSi la sécheuse ne démarre pas, vérifier ce qui suit Achever l’installationFermer la porte et vérifier qu’elle s’enclenche solidement Utilisation dun programme automatique Utilisation DE LA SécheuseMise en marche de la sécheuse Verrouillage descommandes Arrêt de la sécheuseArrêt ou remise en marche ChargementConseilspour le séchage et les programmes Témoins lumineuxProgrammes Caractéristiques supplémentaires Grille de séchage Nettoyage de lemplacement de la sécheuse Entretien DE LA SécheuseNettoyage du filtre à charpie Nettoyage à chaque chargeChangementde l’ampoule d’éclairage Du tambour Nettoyage de l’intérieur de la sécheuseRetraitde la charpie accumulée Dépannage Assistance OU Service Garantie DE LA Sécheuse Kitchenaid KitchenAid Canada ne paiera pas pour8557328A All rights reserved

YKEHS01P, KEHS01P specifications

The KitchenAid KEHS01P and YKEHS01P stand mixers are emblematic of KitchenAid's commitment to quality, durability, and innovative design in kitchen appliances. These stand mixers have become essential tools for both amateur home bakers and professional chefs, bringing versatility and performance to every kitchen.

One of the most notable features of the KEHS01P and YKEHS01P is their powerful motor. With a robust engine that delivers reliable torque, these mixers can handle a wide range of tasks, from whipping egg whites to kneading thick bread dough. This level of power ensures that users can mix even the heaviest of ingredients effortlessly.

Both models come equipped with the signature 10-speed slide control, which allows for precise adjustments to suit different mixing techniques and recipes. Whether it’s a slow stir, a moderate mix, or a fast whip, the seamless transition between speeds provides optimal control over the mixing process. This feature is especially beneficial when dealing with delicate ingredients that require a gentle touch.

The tilt-head design of the KEHS01P and YKEHS01P makes it easy to access the mixing bowl and change attachments, allowing for quick ingredient additions and simple cleaning. The mixers are compatible with a wide range of accessories and attachments that expand their functionality, from pasta makers to food grinders, enhancing their versatility in the kitchen.

Another key characteristic of these stand mixers is their sturdy construction. Made with a durable metal housing, the stand mixers provide stability during use and ensure long-lasting performance. Their compact yet powerful design means they can easily fit into any kitchen countertop without sacrificing functionality.

The mixing bowl included with these models is typically a generous 4.5-quart capacity, perfect for preparing large batches of dough or batter. The stainless-steel bowl is not only easy to clean but is also designed to resist rust and wear over time, adding to the longevity of the product.

In addition to functionality, style is not overlooked. KitchenAid offers a variety of colors and finishes, allowing users to find a model that fits their kitchen aesthetic.

Overall, the KitchenAid KEHS01P and YKEHS01P models embody a blend of power, precision, and style. They are designed to inspire culinary creativity while making the baking and cooking experience enjoyable and efficient. With their impressive features and reliable performance, these stand mixers are truly a worthy investment for anyone who loves to cook or bake.
Top Page Image Contents