American Dryer Corp ADS-464 II manual Specifications/Dimensions

Page 10

SECTION II

SPECIFICATIONS/DIMENSIONS

A. SPECIFICATIONS

MAXIMUM CAPACITY (DRY WEIGHT)	460 lbs.		208.66 kg
Total Weight	10,500 lbs.		4,762.7 kg
Total Shipping Weight	10,800 lbs.		4,898.8 kg
Tilt Height	137-1/4"		348.6 cm
Operating Height	114-1/2"		290.83 cm
Full Tilt Depth	117-1/2"		298.45 cm
Operating Depth	95"		241.3 cm
Width	122"		309.88 cm
Tilt Load (REAR TILT)		15º

Tilt Unload (FRONT TILT)		15º

Loading Height from Floor	65-5/8"		166.69 cm
Tumbler (BASKET) Diameter	69-1/8"		175.58 cm
Tumbler (BASKET) Depth	80-5/16"		203.99 cm
Tumbler (BASKET) Volume	175 cu. ft.		4.96 cu. m
Minimum Load Size	250 lbs.		113.4 kg
Maximum Load Size	460 lbs.		208.66 kg
Blower Motor	25 HP		18.64 kw
Tumbler (BASKET) Motors (2 MOTORS)	(2) 5 HP		(2) 3.73 kw
Boiler Horsepower		60 Bhp

Steam Inlet Size Connection	2-1/2" N.P.T.		---
Burner Blower Motor	1-1/2 HP		1.12 kw
Blower Maximum Airflow	13,000 cfm		368 cmm
Maximum Duct Back Pressure	1.25" W.C.		3.1 mbar
Minimum Duct Diamemter	24"		60.96 cm
Compressed Air Pressure Required	80 psi (±10 psi)		552 kPa (± 69 kPa)
Compressed Air Volume Required	20 cf/hr		.57 cm/hr
Compressed Connection	3/8" N.P.T.		---
Shaded areas are stated in metric equivalents

NOTE: ADC reserves the right to make changes in specifications at any time, without notice or obligation.

6

Image 10

Contents ADS-464 Installation/Operator’s Manual Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Power Malfunctions ServiceMotors Section Important InformationSafety Precautions Explosion could ResultPage SPECIFICATIONS/DIMENSIONS SpecificationsDimensions Reassembly of Dryer Installation ProceduresReattach The Control Pendant Arm Reassembly Instructions For Dryers Shipped In Three 3 Pieces Page Location Requirements Internal AIR, ELECTRICAL, and Water Connections Air Front Tilt Piston and Sprinkler LinesPage Temperature Probe, Base, and Tumbler Basket Disconnects Electric Tumbler Basket MotorsPage Pendant Tumbler Basket Junction Box Disconnect Left Drum MotorExternal Supply Connections Condensate return line must be 1-1/4 pipe Exhaust Ducting Page Electrical Requirements Electrical RequirementsLatest Edition Electrical Service Specifications ADS-464 SteamPage Fresh AIR Supply Requirements Steam Information Steam RequirementsShut Down Instructions PRE START-UP Preparation for OperationSuggested Cleaning Schedule Routine MaintenanceCleaning Clean any lint accumulation from inside the heat consoleMonthly Component System Descriptions Tumbler Basket Support and Drive SystemPage Page Main AIR Blower and Heat Reclaimer System Heat Reclaimer Adjustment Remove Electricity from the Unit Compressed AIR System Page Safety Devices Door Open Service SERVICE/PARTS InformationParts Warranty Warranty InformationReturning Warranty Cards Returning Warranty PartsPage Troubleshooting Troubleshooting Table of Contents NumberVerify red Sprinkler Power on main panel to be illuminated Power MalfunctionsMain Disconnect Will Not Turn On If NO, refer to paragraph #1 above Machine Main Power Shuts Down Blue Indicator Off Sprinkler circuit may be defective3CR CRB Not Used Sprinkler Circuit ComponentsSprinkler Circuit Description Page Emergency Stop E-Stop Buttons 1, 2, Malfunctioning PLC Programmable Logic ControllerPage PLC Message HI-TEMP Fault General DescriptionPage Page Tumbler Basket Section Electrical Malfunctions IntroductionDrum Rotation Sensor PRS1 Rear Panel Control Problems Emergency Stop E-Stop Function If YES, refer to section #3a If NO, refer to section #3b PLC OUT PIN 1 = Drum Reverse PLC OUT PIN 2 = Drum Forward PLC OUT PIN 7 = Unload Door Open PLC OUT PIN 10 = Front UP Wiring Back the PLC Programmable Logic Controller DS1-B=LOAD Door Switch DS2-B=UNLOAD Door SwitchProbable Solutions Base Section Electrical Malfunctions Lint Drawer Proximity Switches Wiring Back to the PLC Programmable Logic ControllerPage Probable Causes Load Level Unload Tumbler Reverse Tumbler Forward ADS-464 Pendant Assembly DiagramPendant Control Malfunctions SEL a = Load SEL B = UnloadTumbler Forward Pendant --- PB1 Wiring Back to PLC Programmable Logic Controller Fuse 4 on Main Electrical Panel Faulty SwitchesWiring Diagram Disconnect Plug Faulty Switch Wiring Back to TB1 Temperature SensingAnother Emergency Stop E-Stop Button Temperature Sensing Component Descriptions Exhaust RTD Resistive Temperature Device Sens1With the control voltage OFF Circuit Wiring to the Analog Input Module MotorsVerify current setting Check circuit Check motor Retest ADS-464 Idling ADS-464 Running ADC113074 1- 01/24/00-10