American Dryer Corp MLG-130DR (HSI) installation manual Gas

Page 32

IMPORTANT: Dryer blower motor impellor/fan as viewed from the front must turn in the clockwise (CW) direction, otherwise the dryer efficiency will be drastically reduced and premature component failure can result.

5.Heat Circuit Operational Test a. Gas Models

1)When the dryer is first started (during initial start-up), the burner has a tendency not to ignite on the first attempt. This is because the gas supply piping is filled with air, so it may take a few minutes for this air to be purged from the lines.

2)The dryer is equipped with a Hot Surface Ignition (HSI) system which has internal diagnostics. If ignition is not established after three (3) attempts, the heat circuit HSI module will LOCKOUT until it is manually reset. To reset the HSI system, open and close the main door and restart the dryer (press the “ENTER/START” key).

NOTE: During the purging period, check to be sure that ALL gas shut-off valves are open.

3)Once ignition is established, a gas pressure test should be taken at the gas valve pressure tap of each dryer to assure that the water column (W.C.) pressure is correct and consistent.

NOTE: Water column pressure requirements (measured at the gas valve pressure tap)...

Natural Gas ----

3.5 Inches W.C. (8.7 mb).

L.P. Gas--------

10.5 Inches W.C. (26.1 mb).

IMPORTANT: There is no regulator provided in an L.P. dryer. The water column (W.C.) pressure must be regulated at the source (L.P. tank) or an external regulator must be added to each dryer.

6.Make a complete operational check of ALL safety-related circuits (i.e., lint drawer switch, and sail switch on gas models).

NOTE: To check for proper sail switch operation, open the main door and while holding main door switch plunger in, start the dryer. The dryer should start but the heat circuit should not be activated (on). If the heat (burner) does activate, shut the dryer off and make the necessary adjustments.

7.A reversing tumbler (basket) dryer should never be operated with less than a 60 lb. (2.72 kg) load (dry weight). The size of the load will affect the coast-down and dwell (stop) times. The tumbler (basket) must come to a complete stop before starting in the opposite direction.

a. Microprocessor (computer) Dryer Models

1)Spin and stop are not adjustable in the Automatic Mode and have been preprogrammed into the microprocessor controller (computer) for 150-seconds spin time in the forward direction and 120-seconds in the reverse direction with a 5-second dwell (stop) time.

28

Image 32
Contents MLG-130DR HSI Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section Procedure for Functional Check of Replacement Section Important InformationSafety Precautions What to do if YOU Smell GASPage SPECIFICATIONS/COMPONENT Identification SpecificationsSpecifications Component Identification Dryer Front View Illus. NoDryer Rear View Illus. No Installation Procedures Location RequirementsUNPACKING/SETTING UP Rear of Dryer refer to the illustration onPage Dryer Enclosure Requirements Fresh AIR Supply Requirements Exhaust Requirements Be Reduced Anywhere Down Stream of the Dryer Page Multiple Dryer Common Venting Page Electrical Information Electrical RequirementsElectrical Service Specifications MLG-130DR GasElectrical Connections GAS Information Technical Data Gas Specifications Gas Connections Inlet connection ---------- 1-inch N.P.TType of Gas Liquid Propane L.P. GasPage Preparation for OPERATION/START-UP Preoperational TestsGas Operating Instructions Basket CoatingShut Down Instructions Parts SERVICE/PARTS InformationService Returning Warranty Parts Warranty InformationReturning Warranty Cards Page Routine Maintenance CleaningAdjustments LubricationReversing Timer SPIN/DWELLADJUSTMENTS Timing LegendProcedure for Functional Check Replacement Components Page Start the drying cycle Manual Reset HI-LIMIT Instructions For Phase 6 ModelsADC113130 1- 03/28/00-25