American Dryer Corp AD-15 Phase 7 installation manual Table of Contents

Page 3

IMPORTANT

YOU MUST DISCONNECT AND LOCK OUT THE ELECTRIC SUPPLYAND THE GAS SUPPLY OR STEAM SUPPLY BEFORE ANY COVERS OR PANELS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) STANDARDS.

“Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper operation.”

«Attention: Au moment de l’entretien des commandes, étiquetez tous les fils avant de les débrancher. Des erreurs de câblage peuvent entraîner un fonctionnement inadéquat et dangereux.»

CAUTION

DRYERS SHOULD NEVER BE LEFT UNATTENDED WHILE IN OPERATION.

When discarding or storing your old clothes dryer,

REMOVE THE DOOR.

Lorsque vous entreposez ou mettez votre sécheuse au rebut, ENLEVEZ-EN LA PORTE.

Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

Ne laissez pas les enfants jouer dans ou sur l’appareil. Il est important de surveiller étroitement les enfants lorsque l’appareil est utilisé non loin d’enfants.

FOR YOURSAFETY

DO NOT DRY MOP HEADS IN THE DRYER.

DO NOT USE DRYER IN THE PRESENCE OF DRY CLEANING FUMES.

WARNING

UNDER NO CIRCUMSTANCES should the dryer main door switch, lint drawer switch, or the heat circuit devices ever be disabled.

WARNING

The dryer must never be operated with any of the back guards, outer tops, or service panels removed.

PERSONAL INJURY OR FIRE COULD RESULT.

WARNING

DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN IN PLACE, EVEN IFAN EXTERNAL LINT COLLECTION SYSTEM IS USED.

IMPORTANT

PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation manual included with the dryer.

Dryer must not be installed or stored in an area where it will be exposed to water or weather.

The wiring diagram for the dryer is located behind the front control panel.

IMPORTANT

Dryer must be installed in a location/environment, which the ambient temperature remains between 40° F (4.44° C) and 130° F (54.44° C).

Table of Contents

 

SAFETY PRECAUTIONS

2

SPECIFICATIONS

3

INSTALLATION PROCEDURES

4

Unpacking/Setting Up

4

Location Requirements

4

Dryer Enclosure Requirements

5

Fresh Air Supply Requirements

5

Exhaust Requirements

5

Electrical Information

8

Gas Information

12

Steam Information

13

Preparation For Operation/Start-Up

16

Preoperational Tests

16

Preoperational Instructions

17

Shutdown Instructions

19

SERVICE/PARTS INFORMATION

19

Service

19

Parts

19

WARRANTY INFORMATION

19

Returning Warranty Cards

19

Warranty

19

Returning Warranty Parts

19

ROUTINE MAINTENANCE

20

Cleaning

20

Adjustments

21

Lubrication

21

DATA LABEL INFORMATION

21

PROCEDURE FOR FUNCTIONAL

 

CHECK OF REPLACEMENT

 

COMPONENTS

22

MANUAL RESET BURNER

 

HI-LIMIT INSTRUCTIONS

24

Phase 7

24

Dual Timer

24

SENSOR ACTIVATED FIRE

 

EXTINGUISHING (S.A.F.E.) SYSTEM ....

25

Image 3
Contents ADC Part No AD-15 Phase Installation ManualDate of Purchase Model no RESELLER’S Name Serial Numbers Retain This Manual In a Safe Place For Future ReferenceTable of Contents Safety Precautions What to do if YOU Smell GASLatest Edition FIP SpecificationsInstallation Procedures UNPACKING/SETTING UPLocation Requirements Dryer Enclosure Requirements Fresh AIR Supply RequirementsExhaust Requirements Single Dryer Venting Horizontal VentingIllus. a Vertical Venting Illus. B Illus. CMultiple Dryer Common Venting Electrical Information Important Venting RemindersGrounding Gas and Steam Models OnlyElectrical Connections KLWHRU5HGFor 110V Applications For 208-230/240V Applications Gas Supply GAS InformationSteam Information Never Test for Leaks with a FlameVoid the Warranty 1RUPDO 0LQLPXP6XSSO\0DLPXP6XSSO\ GAS and Electric Models the sail switch Preparation for OPERATION/START-UPPreoperational Tests GAS and Electric Models only Sail Switch Basket Tumbler CoatingPreoperational Instructions MIN Remain Reversing Timer SPIN/DWELL AdjustmentsWarranty Information SERVICE/PARTS InformationRoutine Maintenance CleaningSuggested Cleaning Schedule Data Label Information Procedure for 113243-1 Manual Reset Burner HI-LIMIT Instructions PhaseDual Timer Before YOU Start Check Local Codes and Permits InstallationOptional Manual Bypass Coin NON-COINF.E. System Parts Break Down F.E. System Diagnostics MessagesADC 113243 1 2/03/04