Raymarine ST1000 Plus & ST2000 Plus manual ST1000+ and ST2000+ Tiller drives socket template

Page 71

ST1000+ and ST2000+

tiller drives: socket template

Drill 2.5 mm (3/32 inch) diameter pilot hole (4 positions)

Drill 21 mm (53/64 inch) diameter hole

D3362-2

Image 71

Contents ST1000 Plus ST2000 Plus Tiller Pilots ST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Contents Index Adjusting Tiller Pilot SettingsCommissioning the Tiller Pilot SeaTalk and Nmea compatibility IntroductionOverview Operating modesEMC conformance SpecificationsGeneral specifications Important Information About this handbookSafety notices Part Using Tiller Pilot Part 1 Using the Tiller Pilot Press standby Using the Tiller PilotDisengaging the autopilot Standby mode Using Auto modeEngaging the autopilot Auto mode Changing course Dodging obstacles Automatic tack feature AutoTackReturning to the previous heading Off course alarmCancelling the off course alarm Automatic deadband control Auto Seastate Displaying navigation information pagesOperating hints trim changes Gusting conditions Switching display illumination on and offAutomatic track acquisition Using Track modeSelecting Track mode Manual track acquisition Manual track acquisition at low speeds Returning to Auto from Track modeCross track error XTE Tidal stream compensation Advance Dodges in Track modeWaypoint arrival and advance ArrivalVerifying computed positions Safety in Track modeSetting waypoints Confirming position at the start of a journeyTrack data not received Track data errorLarge cross track error Waypoint advance Selecting WindTrim mode Using WindTrim modeReturning to the previous apparent wind angle Exiting WindTrim modeWind shift alarm Operating hints for WindTrim mode Using the Tiller Pilot General maintenance Maintenance & Fault FindingProduct support Fault findingSymptomsolution Maintenance & Fault Finding Part Installing Tiller Pilot Part 2 Installing the Tiller Pilot Planning the installation Installing the Tiller PilotCabling guidelines EMC installation guidelinesConnections to other equipment EMC suppression ferritesMeasuring the critical dimensions Installing the tiller pin and mounting socketBasic installation Pushrod Extensions Installation accessoriesInstalling the tiller pin Installing the mounting socketMounting the pushrod extension Dimension C Pushrod extension length LIdentifying the correct tiller bracket Tiller bracketsCutting the cantilever rod to length Cantilever mountingMounting the tiller bracket Dimension F Cut length L Mounting the cantilever assemblyIdentifying the correct pedestal socket Pedestal socket mountingDescription Size Alternative tiller pinsDimension G Pedestal socket length L Mounting the pedestal socketMounting the socket Cabling and socket installationPower supply Cable length Copper area SeaTalk cablingType Length D284 Flat moulded plugs at each end 3 ft 3 D285 Recognized Nmea data Remote control cablingNmea cabling Information Nmea 0183 data Connecting Nmea and SeaTalkOperating sense Switch onCommissioning the Tiller Pilot Functional testsReversing the operating sense Checking the navigation interfaceTrack data not received Navigation error screensTrack data error Checking the SeaTalk interface Checking the wind instrument interfaceInitial sea trial Before starting the sea trial Calibrating the compassAutomatic compass deviation correction Heading alignment Autopilot operation Adjusting autopilot performanceFurther adjustments to heading alignment If this occurs the rudder gain is set correctly Commissioning the Tiller Pilot Introduction Adjusting Tiller Pilot SettingsAdjusting calibration values Calibration menu SettingsFeature Default setting Adjusted values Calibration featuresDefault calibration values Calibration Level 5 cruise speed Calibration Level 6 off course alarm angleCalibrating the tiller pilot Calibration Level 1 Rudder gainCalibration Level 9 magnetic variation Calibration Level 10 heading error correctionCalibration Level 13 rudder damping Controlling access to calibrationCalibration Level 11 boat’s current latitude ST1000+ and ST2000+ Tiller drives socket template Page Nmea IndexST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Warranty Limitations Limited Warranty CertificateUnited States of America UK, Europe, Middle East, Far East Factory Service Centers