Raymarine ST1000 Plus & ST2000 Plus manual Limited Warranty Certificate, Warranty Limitations

Page 75

Limited Warranty Certificate

Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below.

Defects will be corrected by Raymarine or an authorized Raymarine dealer. Raymarine will, except as provided below, accept labor cost for a period of 2 years/24 months from the date of sale to end user. During this period, except for certain products, travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometres) and travel time of 2 hours, will be assumed by Raymarine only on products where proof of installation or commission by authorized service agents, can be shown.

Warranty Limitations

Raymarine Warranty policy does not apply to equipment which has been subjected to accident, abuse or misuse, shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or equipment on which the serial number has been altered, mutilated or removed.

Except where Raymarine or its authorized dealer has performed the installation, it assumes no responsibility for damage incurred during installation.

This Warranty does not cover routine system checkouts or alignment/calibration, unless required by replacement of part(s) in the area being aligned.

A suitable proof of purchase, showing date, place, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service.

Consumable items, (such as: Chart paper, lamps, fuses, batteries, styli, stylus/drive belts, radar mixer crystals/diodes, snap-in impeller carriers, impellers, impeller bearings, and impeller shaft) are specifically excluded from this Warranty.

Magnetrons, Cathode Ray Tubes (CRT), TFT Liquid Crystal Displays (LCD) and cold cathode fluorescent lamps (CCFL), hailer horns and transducers are warranted for 1 year/12 months from date of sale. These items must be returned to a Raymarine facility.

All costs associated with transducer replacement, other than the cost of the transducer itself, are specifically excluded from this Warranty.

Overtime premium labor portion of services outside of normal working hours is not covered by this Warranty.

Travel cost allowance on certain products with a suggested retail price below $2500.00 is not authorized. When/or if repairs are necessary, these products must be forwarded to a Raymarine facility or an authorized dealer at owner’s expense will be returned via surface carrier at no cost to the owner.

Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded on all products. Travel costs which are excluded from the coverage of this Warranty include but are not limited to: taxi, launch fees, aircraft rental, subsistence, customs, shipping and communication charges etc. Travel costs, mileage and time, in excess to that allowed must have prior approval in writing.

TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW:

(1)THIS WARRANTY IS STRICTLY LIMITED TO THE TERMS INDICATED HEREIN, AND NO OTHER WARRANTIES OR REMEDIES SHALL BE BINDING ON RAYMARINE INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABLE OR FITNESS FOR A PARTICULAR PURPOSE.

(2)Raymarine shall not be liable for any incidental, consequential or special (including punitive or multiple) damages.

All Raymarine products sold or provided hereunder are merely aids to navigation. It is the responsibility of the user to exercise discretion and proper navigational skill independent of any Raymarine equipment.

Document number: 84064-8 April 2001

Image 75
Contents ST1000 Plus ST2000 Plus Tiller Pilots ST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Contents Adjusting Tiller Pilot Settings Commissioning the Tiller PilotIndex SeaTalk and Nmea compatibility IntroductionOverview Operating modesSpecifications General specificationsEMC conformance Important Information About this handbookSafety notices Part Using Tiller Pilot Part 1 Using the Tiller Pilot Press standby Using the Tiller PilotUsing Auto mode Engaging the autopilot Auto modeDisengaging the autopilot Standby mode Changing course Dodging obstacles Automatic tack feature AutoTackOff course alarm Cancelling the off course alarmReturning to the previous heading Automatic deadband control Auto Seastate Displaying navigation information pagesOperating hints trim changes Gusting conditions Switching display illumination on and offUsing Track mode Selecting Track modeAutomatic track acquisition Manual track acquisition Returning to Auto from Track mode Cross track error XTEManual track acquisition at low speeds Tidal stream compensation Advance Dodges in Track modeWaypoint arrival and advance ArrivalVerifying computed positions Safety in Track modeSetting waypoints Confirming position at the start of a journeyTrack data error Large cross track errorTrack data not received Waypoint advance Selecting WindTrim mode Using WindTrim modeExiting WindTrim mode Wind shift alarmReturning to the previous apparent wind angle Operating hints for WindTrim mode Using the Tiller Pilot General maintenance Maintenance & Fault FindingProduct support Fault findingSymptomsolution Maintenance & Fault Finding Part Installing Tiller Pilot Part 2 Installing the Tiller Pilot Planning the installation Installing the Tiller PilotCabling guidelines EMC installation guidelinesConnections to other equipment EMC suppression ferritesMeasuring the critical dimensions Installing the tiller pin and mounting socketBasic installation Pushrod Extensions Installation accessoriesInstalling the tiller pin Installing the mounting socketMounting the pushrod extension Dimension C Pushrod extension length LIdentifying the correct tiller bracket Tiller bracketsCantilever mounting Mounting the tiller bracketCutting the cantilever rod to length Dimension F Cut length L Mounting the cantilever assemblyIdentifying the correct pedestal socket Pedestal socket mountingDescription Size Alternative tiller pinsDimension G Pedestal socket length L Mounting the pedestal socketMounting the socket Cabling and socket installationPower supply Cable length Copper area SeaTalk cablingType Length D284 Flat moulded plugs at each end 3 ft 3 D285 Remote control cabling Nmea cablingRecognized Nmea data Information Nmea 0183 data Connecting Nmea and SeaTalkOperating sense Switch onCommissioning the Tiller Pilot Functional testsReversing the operating sense Checking the navigation interfaceNavigation error screens Track data errorTrack data not received Checking the SeaTalk interface Checking the wind instrument interfaceInitial sea trial Calibrating the compass Automatic compass deviation correctionBefore starting the sea trial Heading alignment Adjusting autopilot performance Further adjustments to heading alignmentAutopilot operation If this occurs the rudder gain is set correctly Commissioning the Tiller Pilot Adjusting Tiller Pilot Settings Adjusting calibration valuesIntroduction Calibration menu SettingsCalibration features Default calibration valuesFeature Default setting Adjusted values Calibration Level 5 cruise speed Calibration Level 6 off course alarm angleCalibrating the tiller pilot Calibration Level 1 Rudder gainCalibration Level 9 magnetic variation Calibration Level 10 heading error correctionControlling access to calibration Calibration Level 11 boat’s current latitudeCalibration Level 13 rudder damping ST1000+ and ST2000+ Tiller drives socket template Page Nmea IndexST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Warranty Limitations Limited Warranty CertificateUnited States of America UK, Europe, Middle East, Far East Factory Service Centers