Raymarine ST1000 Plus & ST2000 Plus manual Calibration Level 11 boat’s current latitude

Page 70

6 Adjusting Tiller Pilot Settings

66

ST1000 Plus & ST2000 Plus Tiller Pilots - Owner’s Handbook

Calibration Level 11: boat’s current latitude

When you have switched on heading error correction (Level 10), you need to use Calibration Level 11 to input the boat’s current latitude (to the nearest degree).

Set the latitude using the -1, +1, -10and +10 keys.

Note: If the correction is switched off in Calibration Level 10 (i.e. set to ‘0’),Level 11 will be omitted. When you press the auto key in Calibration Level 10 you will advance to Level 13.

Calibration Level 13: rudder damping

Adjust the value in Calibration Level 13 if the tiller drive ‘hunts’ when trying to position the rudder.

you can select 9 stages of rudder damping – initially, this option should be set to 3

if the autopilot is over-active in calm conditions, increase the damping

if the course keeping is not tight enough, decrease the damping

adjust the damping one stage at a time

Controlling access to calibration

You can prevent unauthorized access to calibration as follows:

1.Press and hold -1and standby together for 10 seconds until the display shows CAL OFF:

D214-1

2.Toggle the calibration access between On and OFF using the -1and +1 keys.

3.Store the setting by pressing -1and standby for 10 seconds until the tiller drive returns to normal operation.

Image 70
Contents ST1000 Plus ST2000 Plus Tiller Pilots ST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Contents Commissioning the Tiller Pilot Adjusting Tiller Pilot SettingsIndex Operating modes IntroductionOverview SeaTalk and Nmea compatibilityGeneral specifications SpecificationsEMC conformance About this handbook Important InformationSafety notices Part Using Tiller Pilot Part 1 Using the Tiller Pilot Using the Tiller Pilot Press standbyEngaging the autopilot Auto mode Using Auto modeDisengaging the autopilot Standby mode Changing course Automatic tack feature AutoTack Dodging obstaclesCancelling the off course alarm Off course alarmReturning to the previous heading Displaying navigation information pages Automatic deadband control Auto SeastateOperating hints trim changes Switching display illumination on and off Gusting conditionsSelecting Track mode Using Track modeAutomatic track acquisition Manual track acquisition Cross track error XTE Returning to Auto from Track modeManual track acquisition at low speeds Tidal stream compensation Arrival Dodges in Track modeWaypoint arrival and advance AdvanceConfirming position at the start of a journey Safety in Track modeSetting waypoints Verifying computed positionsLarge cross track error Track data errorTrack data not received Waypoint advance Using WindTrim mode Selecting WindTrim modeWind shift alarm Exiting WindTrim modeReturning to the previous apparent wind angle Operating hints for WindTrim mode Using the Tiller Pilot Maintenance & Fault Finding General maintenanceFault finding Product supportSymptomsolution Maintenance & Fault Finding Part Installing Tiller Pilot Part 2 Installing the Tiller Pilot Installing the Tiller Pilot Planning the installationEMC installation guidelines Cabling guidelinesEMC suppression ferrites Connections to other equipmentInstalling the tiller pin and mounting socket Measuring the critical dimensionsBasic installation Installing the mounting socket Installation accessoriesInstalling the tiller pin Pushrod ExtensionsDimension C Pushrod extension length L Mounting the pushrod extensionTiller brackets Identifying the correct tiller bracketMounting the tiller bracket Cantilever mountingCutting the cantilever rod to length Mounting the cantilever assembly Dimension F Cut length LPedestal socket mounting Identifying the correct pedestal socketMounting the pedestal socket Alternative tiller pinsDimension G Pedestal socket length L Description SizeCabling and socket installation Mounting the socketPower supply SeaTalk cabling Cable length Copper areaType Length D284 Flat moulded plugs at each end 3 ft 3 D285 Nmea cabling Remote control cablingRecognized Nmea data Connecting Nmea and SeaTalk Information Nmea 0183 dataFunctional tests Switch onCommissioning the Tiller Pilot Operating senseChecking the navigation interface Reversing the operating senseTrack data error Navigation error screensTrack data not received Checking the wind instrument interface Checking the SeaTalk interfaceInitial sea trial Automatic compass deviation correction Calibrating the compassBefore starting the sea trial Heading alignment Further adjustments to heading alignment Adjusting autopilot performanceAutopilot operation If this occurs the rudder gain is set correctly Commissioning the Tiller Pilot Adjusting calibration values Adjusting Tiller Pilot SettingsIntroduction Settings Calibration menuDefault calibration values Calibration featuresFeature Default setting Adjusted values Calibration Level 1 Rudder gain Calibration Level 6 off course alarm angleCalibrating the tiller pilot Calibration Level 5 cruise speedCalibration Level 10 heading error correction Calibration Level 9 magnetic variationCalibration Level 11 boat’s current latitude Controlling access to calibrationCalibration Level 13 rudder damping ST1000+ and ST2000+ Tiller drives socket template Page Index NmeaST1000 Plus & ST2000 Plus Tiller Pilots Owner’s Handbook Limited Warranty Certificate Warranty LimitationsFactory Service Centers United States of America UK, Europe, Middle East, Far East