Furuno SC-60 Display unit, processor unit, Example of antenna installed below superstructures

Page 17

Location influenced by reflected wave.

SC-series

Antenna

Radar Antenna

Reception blocked by mast.

Bridge

Example of antenna installed below superstructures

2.1.2Display unit, processor unit

Choose a location where vibration and shock are minimal.

Install the units well away from locations subject to rain and water splash.

Locate the units away from air conditioner vents.

Keep the units out of direct sunlight because of heat that can build up inside their cabinets.

Choose a well-ventilated location.

For the display unit, choose a location where it can be easily operated.

Leave sufficient space around the units to permit access for maintenance. See the outline drawing for recommended maintenance space.

2-3

Image 17
Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Iii Appendix B Installation of Antenna Unit SC-603Word to the Owner of the SC-60 FeaturesForeword System configuration System ConfigurationDgps Equipment ListName Type Code No Qty Remarks Vii Software Version ListThis page is intentionally left blank Interface SC-60General Coating Color Power SupplyEnvironmental Condition and EMC Principle of satellite compass operation Principle of OperationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Mast diameter Separation distance minimum InstallationHorizontal separation between antenna and masts Antenna and field of viewDisplay unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsHow to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverMounting the Dgps antenna Dgps antenna unitAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Direction a Direction B Processor Unit, rear viewAdjusting for orientation error Installing the Display UnitDesktop, overhead mounting Display unit mounting methodsFlush mount F Flush mountName Type Flush mount SGeneral wiring diagram WiringAntenna TPPX6-3D2V-15M Port on GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuChoosing heading source Heading setup menuPort Format Setting Remarks Jumper wire and format on the circuit board 20P8171Heading data format Processor unit, cover opened, top viewTNCBPJ140 Installing the Dgps Beacon Receiver KitConnection of External Equipment Processor unit, cover removed, top view ProcedureJ10 20P8171 Display unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarm menu, GPS buzzer options AlarmsAlarm menu Satellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Output DataInterface Navigation dataNAV OUT menu OFFTalker identifier mnemonics Log pulseLog pulse rate selection window Heading talker selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode Dgps SetupManual Dgps setup Dgps menuBeacon receiver selection window INTStation Nearest Programming user beacon stationsBeacon station display Station UserDisplay for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others menu Others MenuReset Distance prompt Resetting Distance RunTrip Menu Trip menuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Diagnostics TroubleshootingSymptom Cause Remedy Diagnostic test1LCD Check MAINTENANCE, TroubleshootingDiagnostic test sequence TEST2 display Diagnostic test2Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryBattery exchange options Prompt for exchanging batteryError Messages Replacement of FuseError Message Meaning Remedy Message displayError messages con’t from previous Menu Tree Appendix aNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic Appendix a VDR Set and driftVTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListHow to orient the antenna elements Installing the Antenna UnitAppendix B Antenna unit SC-603Fixing antenna unit to pedestal Appendix BOrienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the Antenna Unit Antenna element Fastening the antenna cableThis page is intentionally left blank Packing List SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index-1 Index