Furuno SC-60 manual Bulkhead mount, Processor unit, top view, Angular rate sensor, top view

Page 24

2. INSTALLATION

2.3.2Bulkhead mount

For mounting on a bulkhead, use the bulkhead mounting plate supplied with the installation materials.

1.Unfasten four screws from the top cover to open the front panel.

2.Unfasten two screws to dismount the angular rate sensor.

Angular Rate Sensor

BEACON

20P8171

Processor unit, top view

3.Fasten the bulkhead mounting plate to the angular rate sensor. Align the center graduation on the sensor with the hole of the bulkhead mounting plate and tighten fixing screws.

	Hole of bulkhead
Scale	mounting plate
Scale
Center Mark

Angular Rate Sensor

Mounting Base

Fixing Screw

Angular rate sensor, top view

2-10

Image 24

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 IiiFeatures ForewordWord to the Owner of the SC-60 System Configuration System configurationEquipment List Name Type Code No Qty RemarksDgps Software Version List ViiThis page is intentionally left blank SC-60 GeneralInterface Power Supply Environmental Condition and EMCCoating Color Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Installation Mounting ConsiderationsSC-series antenna unit Installation Mast diameter Separation distance minimumHorizontal separation between antenna and masts Antenna and field of viewExample of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaWaterproofing the antenna connector How to fasten the antenna cableCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitDgps antenna unit Mounting the Dgps antennaWaterproofing the extension connector Cable connection when using cable RG-10UYAntenna cable set Type OP08-17, Code No Installing the Processor Unit Deck mountProcessor unit orientation, deck mounting Bulkhead mount Processor unit, top viewAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation on the underside of a desk Installation of processor unit on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Direction a Direction BInstalling the Display Unit Adjusting for orientation errorDesktop, overhead mounting Display unit mounting methodsFlush mount Flush mount FName Type Flush mount SWiring General wiring diagramAntenna TPPX6-3D2V-15M Port on GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuHeading setup menu Choosing heading sourceJumper wire and format on the circuit board 20P8171 Port Format Setting RemarksHeading data format Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentTNCBPJ140 Procedure Processor unit, cover removed, top viewJ10 20P8171 Operation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarms Alarm menuAlarm menu, GPS buzzer options Alarm menu, Dgps buzzer options Confirming Satellite StatusSatellite status display GPS Setup Displaying the GPS setup menuGPS Setup menu description Output Data HeadingNavigation data InterfaceNAV OUT menu OFFLog pulse Talker identifier mnemonicsLog pulse rate selection window Heading talker selection windowSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Dgps Setup Demonstration modeManual Dgps setup Dgps menuINT Beacon receiver selection windowProgramming user beacon stations Station NearestBeacon station display Station UserEditing user beacon stations NEW User Channel displayDisplay for editing user channels Erasing individual user stations Erasing all user beacon stationsPrompt for erasure of all user channels Others Menu Others menuResetting Distance Run Reset Distance promptTrip Menu Trip menuThis page is intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceDo not open the equipment Troubleshooting DiagnosticsSymptom Cause Remedy Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceLCD Check Diagnostic test2 TEST2 displayProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoBattery exchange options Prompt for exchanging batteryReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous Appendix a Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift Appendix aVTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OInstalling the Antenna Unit How to orient the antenna elementsAppendix B Antenna unit SC-603Appendix B Fixing antenna unit to pedestalOrient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the Antenna Unit Fastening the antenna cable Antenna elementThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1