Furuno manual Appendix B, Installing the Antenna Unit, Antenna unit SC-603

Page 79

APPENDIX B

Installation of Antenna Unit SC-603

B.1 Mounting Considerations

See the mounting considerations on page 2-1 to select a suitable mounting location. (The drawings are for the antenna unit SC-303, but the guidelines are the same.)

B.2 Installing the Antenna Unit

1.Screw in three antenna elements in the Antenna Base S. Remove Antenna Cover S and Arm cover S.

Antenna Cover S

3

Arm Cover S (Below arm)

1

Antenna Base S

2

Antenna

Element

Antenna unit SC-603

2.Pass the coaxial cable from each antenna element through the center of the respective arm and then through the hole at the center of the antenna unit.

3.Orient the three antenna elements so that the protrusion on each faces the bow.

Nut

BOW

Orient the three antenna elements so the protrusion

on each faces the bow.

Arm Cover S

How to orient the antenna elements

B-1

Image 79

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Iii Appendix B Installation of Antenna Unit SC-603Foreword FeaturesWord to the Owner of the SC-60 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListDgps Vii Software Version ListThis page is intentionally left blank General SC-60Interface Environmental Condition and EMC Power SupplyCoating Color Principle of satellite compass operation Principle of OperationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Antenna and field of view InstallationMast diameter Separation distance minimum Horizontal separation between antenna and mastsDisplay unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsCable from antenna No. marked on cable Waterproofing the antenna connectorHow to fasten the antenna cable Coating bolt, nut and washers with silicone sealantAntenna unit How to insert the cable coverMounting the Dgps antenna Dgps antenna unitCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Direction a Direction B Processor Unit, rear viewDisplay unit mounting methods Installing the Display UnitAdjusting for orientation error Desktop, overhead mountingFlush mount S Flush mountFlush mount F Name TypeGPS ANT WiringGeneral wiring diagram Antenna TPPX6-3D2V-15M Port onHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBMain menu Initial SettingsInstallation setup menu Confirming satellite status choosing mounting methodChoosing heading source Heading setup menuProcessor unit, cover opened, top view Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Heading data formatConnection of External Equipment Installing the Dgps Beacon Receiver KitTNCBPJ140 Processor unit, cover removed, top view ProcedureJ10 20P8171 Controls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Nav data display Choosing a DisplayDescription of displays Heading displaySet and Drift display, Distance Run display Steering displayCompass display ROT Rate-of-Turn displayAlarm menu AlarmsAlarm menu, GPS buzzer options Confirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Heading Output DataOFF Navigation dataInterface NAV OUT menuHeading talker selection window Log pulseTalker identifier mnemonics Log pulse rate selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Dgps menu Dgps SetupDemonstration mode Manual Dgps setupBeacon receiver selection window INTStation User Programming user beacon stationsStation Nearest Beacon station displayNEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others menu Others MenuTrip menu Resetting Distance RunReset Distance prompt Trip MenuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Diagnostic test1 TroubleshootingDiagnostics Symptom Cause RemedyDiagnostic test sequence MAINTENANCE, TroubleshootingLCD Check TEST2 display Diagnostic test2Prompts for erasure of data Program NumberClearing Data Program version no. displayPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Battery exchange optionsMessage display Replacement of FuseError Messages Error Message Meaning RemedyError messages con’t from previous Menu Tree Appendix aNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic Appendix a VDR Set and driftVTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListAntenna unit SC-603 Installing the Antenna UnitHow to orient the antenna elements Appendix BFixing antenna unit to pedestal Appendix BOrienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the Antenna Unit Antenna element Fastening the antenna cableThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index-1 Index