Furuno SC-60 manual 00080919106

Page 2

9-52 Ashihara-cho,

Nishinomiya, Japan

Telephone : 0798-65-2111

fax	: 0798-65-4200

All rights reserved.

Printed in Japan

PUB.No. OME-72480

( KAMI ) SC-60

Your Local Agent/Dealer

FIRST EDITION : FEB. 2001 U1 : FEB. 26,2004

00080919106

*00080919106*

* 0 0 0 8 0 9 1 9 1 0 6 *

*OME72480U10*

*OME72480U10*

* O M E 7 2 4 8 0 U 1 0 *

Image 2

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 IiiWord to the Owner of the SC-60 FeaturesForeword System Configuration System configurationDgps Equipment ListName Type Code No Qty Remarks Software Version List ViiThis page is intentionally left blank Interface SC-60General Coating Color Power SupplyEnvironmental Condition and EMC Principle of Operation Principle of satellite compass operationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Horizontal separation between antenna and masts InstallationMast diameter Separation distance minimum Antenna and field of viewExample of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaCoating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitDgps antenna unit Mounting the Dgps antennaAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Direction a Direction BDesktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methodsName Type Flush mountFlush mount F Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuHeading setup menu Choosing heading sourceHeading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top viewTNCBPJ140 Installing the Dgps Beacon Receiver KitConnection of External Equipment Procedure Processor unit, cover removed, top viewJ10 20P8171 Display unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run displayAlarm menu, GPS buzzer options AlarmsAlarm menu Satellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Output Data HeadingNAV OUT menu Navigation dataInterface OFFLog pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Manual Dgps setup Dgps SetupDemonstration mode Dgps menuINT Beacon receiver selection windowBeacon station display Programming user beacon stationsStation Nearest Station UserDisplay for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others Menu Others menuTrip Menu Resetting Distance RunReset Distance prompt Trip menuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1LCD Check MAINTENANCE, TroubleshootingDiagnostic test sequence Diagnostic test2 TEST2 displayProgram version no. display Program NumberClearing Data Prompts for erasure of dataBattery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Appendix a Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift Appendix aVTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OAppendix B Installing the Antenna UnitHow to orient the antenna elements Antenna unit SC-603Appendix B Fixing antenna unit to pedestalOrient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the Antenna Unit Fastening the antenna cable Antenna elementThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1