Furuno SC-60 Installing the Antenna Units, Mounting dimensions for antenna, orienting the antenna

Page 18

2. INSTALLATION

2.2Installing the Antenna Units

2.2.1SC-series antenna unit

NOTICE

Fasten the antenna to the mounting location lastly if it is more convenient to connect the antenna cable before mounting the antenna unit.

1.Prepare a mounting platform (wood, steel or aluminum) in accordance with the illustration shown below. If corrosive material is used, take necessary anti-corrosion measures.

Note: When drilling holes in the platform, be sure they are parallel with the fore-and-aft line.

2.Fasten the antenna unit to the platform with four sets of M10 hex. bolts, spring washers and flat washers, orienting it as shown below. (The bow mark

( ) on the antenna should face the bow.) The torque for the hex. bolts should be between 19.6-24.5 Nm.

NOTICE

Do not open the antenna.

This installation does not require removal of the antenna cover.

240

160

240

160

N

U

R

F	U

BOW

Fixing Hole (f11 mm)

Flat Washer

Spring Washer Hex. Bolt

Mounting dimensions for antenna, orienting the antenna

2-4

Image 18

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 IiiFeatures ForewordWord to the Owner of the SC-60 System Configuration System configurationEquipment List Name Type Code No Qty RemarksDgps Software Version List ViiThis page is intentionally left blank SC-60 GeneralInterface Power Supply Environmental Condition and EMCCoating Color Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Installation Mounting ConsiderationsSC-series antenna unit Horizontal separation between antenna and masts InstallationMast diameter Separation distance minimum Antenna and field of viewExample of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaCoating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitDgps antenna unit Mounting the Dgps antennaWaterproofing the extension connector Cable connection when using cable RG-10UYAntenna cable set Type OP08-17, Code No Installing the Processor Unit Deck mountProcessor unit orientation, deck mounting Bulkhead mount Processor unit, top viewAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation on the underside of a desk Installation of processor unit on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Direction a Direction BDesktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methodsName Type Flush mountFlush mount F Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuHeading setup menu Choosing heading sourceHeading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentTNCBPJ140 Procedure Processor unit, cover removed, top viewJ10 20P8171 Operation ControlsDisplay unit Turning the Power On/Off Panel Illumination, Display ContrastProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run displayAlarms Alarm menuAlarm menu, GPS buzzer options Alarm menu, Dgps buzzer options Confirming Satellite StatusSatellite status display GPS Setup Displaying the GPS setup menuGPS Setup menu description Output Data HeadingNAV OUT menu Navigation dataInterface OFFLog pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection windowSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Manual Dgps setup Dgps SetupDemonstration mode Dgps menuINT Beacon receiver selection windowBeacon station display Programming user beacon stationsStation Nearest Station UserEditing user beacon stations NEW User Channel displayDisplay for editing user channels Erasing individual user stations Erasing all user beacon stationsPrompt for erasure of all user channels Others Menu Others menuTrip Menu Resetting Distance RunReset Distance prompt Trip menuThis page is intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceDo not open the equipment Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceLCD Check Diagnostic test2 TEST2 displayProgram version no. display Program NumberClearing Data Prompts for erasure of dataBattery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Appendix a Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift Appendix aVTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OAppendix B Installing the Antenna UnitHow to orient the antenna elements Antenna unit SC-603Appendix B Fixing antenna unit to pedestalOrient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the Antenna Unit Fastening the antenna cable Antenna elementThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1