Furuno SC-60 manual Fastening the antenna cable, Antenna element

Page 83

APPENDIX B

7.Make a loop in the antenna cable as shown in the illustration below. Fasten the antenna cable to the antenna mast with cable ties.

Coat with Three

Bond 1211 (supplied).

Coat bolt threads with Three Bond and then coat nuts with the Three Bond.

Fix antenna cable to mast with cable ties.

Fastening the antenna cable

8.Coat bolt threads and nuts at the bottom of each antenna element with Three Bond 1211.

9.Paint pedestal and support plate with anti-corrosive paint.

10.If necessary, attach the “bird-repellent fixtures” (supplied) to each antenna element and the Antenna Cover S as shown below.

Bird-repellent fixture

Antenna element

B-5

Image 83

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Iii Appendix B Installation of Antenna Unit SC-603Word to the Owner of the SC-60 FeaturesForeword System configuration System ConfigurationDgps Equipment ListName Type Code No Qty Remarks Vii Software Version ListThis page is intentionally left blank Interface SC-60General Coating Color Power SupplyEnvironmental Condition and EMC Principle of satellite compass operation Principle of OperationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Antenna and field of view InstallationMast diameter Separation distance minimum Horizontal separation between antenna and mastsDisplay unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsCable from antenna No. marked on cable Waterproofing the antenna connectorHow to fasten the antenna cable Coating bolt, nut and washers with silicone sealantAntenna unit How to insert the cable coverMounting the Dgps antenna Dgps antenna unitAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Direction a Direction B Processor Unit, rear viewDisplay unit mounting methods Installing the Display UnitAdjusting for orientation error Desktop, overhead mountingFlush mount S Flush mountFlush mount F Name TypeGPS ANT WiringGeneral wiring diagram Antenna TPPX6-3D2V-15M Port onHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBMain menu Initial SettingsInstallation setup menu Confirming satellite status choosing mounting methodChoosing heading source Heading setup menuProcessor unit, cover opened, top view Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Heading data formatTNCBPJ140 Installing the Dgps Beacon Receiver KitConnection of External Equipment Processor unit, cover removed, top view ProcedureJ10 20P8171 Display unit OperationControls Processor unit Turning the Power On/OffPanel Illumination, Display Contrast Nav data display Choosing a DisplayDescription of displays Heading displaySet and Drift display, Distance Run display Steering displayCompass display ROT Rate-of-Turn displayAlarm menu, GPS buzzer options AlarmsAlarm menu Satellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Output DataOFF Navigation dataInterface NAV OUT menuHeading talker selection window Log pulseTalker identifier mnemonics Log pulse rate selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Dgps menu Dgps SetupDemonstration mode Manual Dgps setupBeacon receiver selection window INTStation User Programming user beacon stationsStation Nearest Beacon station displayDisplay for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others menu Others MenuTrip menu Resetting Distance RunReset Distance prompt Trip MenuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Diagnostic test1 TroubleshootingDiagnostics Symptom Cause RemedyLCD Check MAINTENANCE, TroubleshootingDiagnostic test sequence TEST2 display Diagnostic test2Prompts for erasure of data Program NumberClearing Data Program version no. displayPrompt for exchanging battery Replacement of BatteryBattery Location Type Code No Battery exchange optionsMessage display Replacement of FuseError Messages Error Message Meaning RemedyError messages con’t from previous Menu Tree Appendix aNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic Appendix a VDR Set and driftVTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListAntenna unit SC-603 Installing the Antenna UnitHow to orient the antenna elements Appendix BFixing antenna unit to pedestal Appendix BOrienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the Antenna Unit Antenna element Fastening the antenna cableThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index-1 Index