Furuno SC-60 manual HEAD1HEAD2HEAD3

Page 25

2. INSTALLATION

4.Loosen four screws on the angular rate sensor mounting base, and then fasten the bulkhead mounting plate to the angular rate sensor mounting base.

Angular Rate Sensor

Angular

Rate

Sensor

Mounting

Base

BEACON

20P8171

Bulkhead Mounting Plate

Top Fixing

Hole (x2)

HEAD1HEAD2HEAD3

Processor unit, top view

5.Close the top cover of the processor unit.

6.Partially screw in two tapping screws for the top fixing holes of the processor unit in the mounting location. Hang the processor unit on the tapping screws, using the top fixing holes. Screw in two tapping screws for the bottom fixing holes, and then tighten the top fixing holes.

2-11

Image 25

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Iii Appendix B Installation of Antenna Unit SC-603Foreword FeaturesWord to the Owner of the SC-60 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListDgps Vii Software Version ListThis page is intentionally left blank General SC-60Interface Environmental Condition and EMC Power SupplyCoating Color Principle of satellite compass operation Principle of OperationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Mast diameter Separation distance minimum InstallationHorizontal separation between antenna and masts Antenna and field of viewDisplay unit, processor unit Example of antenna installed below superstructuresMounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsHow to fasten the antenna cable Waterproofing the antenna connectorCoating bolt, nut and washers with silicone sealant Cable from antenna No. marked on cableAntenna unit How to insert the cable coverMounting the Dgps antenna Dgps antenna unitCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Direction a Direction B Processor Unit, rear viewAdjusting for orientation error Installing the Display UnitDesktop, overhead mounting Display unit mounting methodsFlush mount F Flush mountName Type Flush mount SGeneral wiring diagram WiringAntenna TPPX6-3D2V-15M Port on GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuChoosing heading source Heading setup menuPort Format Setting Remarks Jumper wire and format on the circuit board 20P8171Heading data format Processor unit, cover opened, top viewConnection of External Equipment Installing the Dgps Beacon Receiver KitTNCBPJ140 Processor unit, cover removed, top view ProcedureJ10 20P8171 Controls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarm menu AlarmsAlarm menu, GPS buzzer options Confirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Heading Output DataInterface Navigation dataNAV OUT menu OFFTalker identifier mnemonics Log pulseLog pulse rate selection window Heading talker selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode Dgps SetupManual Dgps setup Dgps menuBeacon receiver selection window INTStation Nearest Programming user beacon stationsBeacon station display Station UserNEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others menu Others MenuReset Distance prompt Resetting Distance RunTrip Menu Trip menuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Diagnostics TroubleshootingSymptom Cause Remedy Diagnostic test1Diagnostic test sequence MAINTENANCE, TroubleshootingLCD Check TEST2 display Diagnostic test2Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryBattery exchange options Prompt for exchanging batteryError Messages Replacement of FuseError Message Meaning Remedy Message displayError messages con’t from previous Menu Tree Appendix aNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic Appendix a VDR Set and driftVTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListHow to orient the antenna elements Installing the Antenna UnitAppendix B Antenna unit SC-603Fixing antenna unit to pedestal Appendix BOrienting the antenna unit Orient the antenna unit as shown in the illustration belowWelding the Antenna Unit Antenna element Fastening the antenna cableThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index-1 Index