Furuno SC-60 manual Schematic diagrams

Page 70

APPENDIX A

Schematic diagrams

HDG IN port (listener)

Load requirements

Isolation: Optocoupler

Input Impedance: 220 ohm

Max. voltage: ±15V

HDG OUT1 port

Output drive capability

Max. 10 mA

A-4

Image 70

Contents Satellite Compass 00080919106 Safety Instructions Table of Contents Appendix B Installation of Antenna Unit SC-603 IiiForeword FeaturesWord to the Owner of the SC-60 System Configuration System configurationName Type Code No Qty Remarks Equipment ListDgps Software Version List ViiThis page is intentionally left blank General SC-60Interface Environmental Condition and EMC Power SupplyCoating Color Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Horizontal separation between antenna and masts InstallationMast diameter Separation distance minimum Antenna and field of viewExample of antenna installed below superstructures Display unit, processor unitInstalling the Antenna Units Mounting dimensions for antenna, orienting the antennaCoating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cableHow to insert the cable cover Antenna unitDgps antenna unit Mounting the Dgps antennaCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Direction a Direction BDesktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methodsName Type Flush mountFlush mount F Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram GPS ANTHow to install the optional antenna cable set How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuHeading setup menu Choosing heading sourceHeading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top viewConnection of External Equipment Installing the Dgps Beacon Receiver KitTNCBPJ140 Procedure Processor unit, cover removed, top viewJ10 20P8171 Controls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run displayAlarm menu AlarmsAlarm menu, GPS buzzer options Confirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Output Data HeadingNAV OUT menu Navigation dataInterface OFFLog pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Manual Dgps setup Dgps SetupDemonstration mode Dgps menuINT Beacon receiver selection windowBeacon station display Programming user beacon stationsStation Nearest Station UserNEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others Menu Others menuTrip Menu Resetting Distance RunReset Distance prompt Trip menuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1Diagnostic test sequence MAINTENANCE, TroubleshootingLCD Check Diagnostic test2 TEST2 displayProgram version no. display Program NumberClearing Data Prompts for erasure of dataBattery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous Appendix a Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift Appendix aVTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OAppendix B Installing the Antenna UnitHow to orient the antenna elements Antenna unit SC-603Appendix B Fixing antenna unit to pedestalOrient the antenna unit as shown in the illustration below Orienting the antenna unitWelding the Antenna Unit Fastening the antenna cable Antenna elementThis page is intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ SC-303 工事材料表 Installation Materials Page Installation Materials Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Page Index Index-1