0025$7856 180%5248,&.0025&+$11/6 | Kenwood TS-590S specs

0(025<)($785(6

180%(52)48,&.0(025<&+$11(/6

This transceiver provides up to 10 Quick Memory channels. You can adjust the number of available channels by accessing Menu No. 17 and selecting “3”, “5” (default), or “10”.

6725,1*,17248,&.0(025<

Each time you store a new frequency, all previously stored frequencies are bumped to the next respective Quick Memory channel. When all 10 memory channels contain frequencies, storing one more frequency bumps the contents of memory channel 9 off the stack (the data is lost).

The following diagram illustrates how the Quick Memory stacks the data in memory each time you press [Q-M.IN].

New data
24.911	14.005	14.235	14.250	18.111
Memory 0	Memory 1	Memory 2	Memory 3	Memory 4
50.015	7.082	29.610	3.545	14.195
Memory 5	Memory 6	Memory 7	Memory 8	Memory 9
New data
21.005	24.911	14.005	14.235	14.250
Memory 0	Memory 1	Memory 2	Memory 3	Memory 4
18.111	50.015	7.082	29.610	3.545
Memory 5	Memory 6	Memory 7	Memory 8	Memory 9
New data
14.085	21.005	24.911	14.005	14.235
Memory 0	Memory 1	Memory 2	Memory 3	Memory 4
14.250	18.111	50.015	7.082	29.610
Memory 5	Memory 6	Memory 7	Memory 8	Memory 9

You can store data in the Quick Memory only when you operate the transceiver in VFO mode.

1Select the frequency, mode, etc., on the transceiver VFO.

2 Press [Q-M.IN].

•Each time you press [Q-M.IN], the current VFO data is written to the Quick Memory.

Note: When RIT or XIT is ON, the ON status and the offset will also be stored.

5(&$//,1*48,&.0(025<&+$11(/6

You can recall a Quick Memory channel only when you operate the transceiver in VFO mode.

1Press [Q-MR].

•The current memory channel number appears.

•If there is no data stored in any Quick Memory channel, the data cannot be recalled to the current VFO; an error beep sounds.

2Turn the MULTI/CH control to select a Quick Memory channel.

•You cannot change memory channels while transmitting.

3To exit, press [Q-MR]again.

Note: Memory channels cannot be changed while using the TF-SET function.

7(0325$5<)5(48(1&<&+$1*(6

After recalling a Quick Memory channel, you can temporarily change the data without overwriting the contents of the channel. You can change the frequency even when you select “oFF” in Menu No. 18.

1Press [Q-MR].

2Turn the MULTI/CH control to select a Quick Memory channel.

3Change the frequencies and associated data.

4To store the changed data in the Quick Memory, press [Q-M.IN].

•This action stores the new data in the current channel and bumps the old frequency to the next higher Quick Memory channel.

5To exit, press [Q-MR]again.

Note: Memory channel data can also be changed while using the TF-SET function.

48,&.0(025<°9)275$16)(5

This function copies the contents of the recalled memory channel to the VFO.

1Recall a Quick Memory channel.

2Press [M>V].

Note: Pressing [M>V] after temporarily changing the recalled data copies the new data to the VFO.

(5$6,1*48,&.0(025<&+$11(/6

1Recall a Quick Memory channel.

2Press and hold [CLR].

•A confirmation message appears on the display.

3Press [CLR].

• The channel data has been erased.

0(025<)($785(6