7528%/(6+227,1*
Problem | Probable Cause | Corrective Action | Page |
A message cannot be | There is a communication | Confirm that the connector of the | 71,78 |
recorded/ played back | error between the transceiver | securely connected to the transceiver. Perform |
|
or no announcement | and the | the Full reset. If the problem persists, contact a |
|
can be heard. |
| Kenwood authorized service center for repairs |
|
|
| (with the |
|
|
|
|
|
The transceiver | Most of the external RF | Apply a continuous single tone (1 kHz) to the | — |
output power seems | power meters measure the | microphone audio input to measure the RF |
|
to be low in SSB | average RF power. So, the | output power. The PEP will be the same as this |
|
mode. | meter reading is low when | RF output level. |
|
| you operate and talk in SSB |
|
|
| mode. The LCD meter used |
|
|
| in the |
|
|
| fast response time but it is not |
|
|
| fast enough to measure the |
|
|
| accurate PEP (Peak Envelope |
|
|
| Power). |
|
|
The PC and external | The input terminal is different | Confirm that the setting of Menu No. 63 matches | 58 |
equipment is not | from the one specified (Menu | the input terminal for the external equipment. |
|
modulating. | No. 63) for the external |
|
|
| equipment. |
|
|
|
|
|
|
0,&52352&(66255(6(7
If your transceiver seems to be malfunctioning, resetting the microprocessor to its default settings may resolve the problem. There are 2 levels
of resetting the microprocessor of the
4Press [A/B (A=B)] to perform the VFO reset.
•A confirmation message appears when performing the VFO Reset. Press [A/B (A=B)] again to proceed. Otherwise, press any other key to cancel the VFO Reset and return to normal operation.
•The VFOs reset to the factory default values.
,1,7,$/6(77,1*6
For each VFO, the factory defaults for the operating frequency and mode are as follows:
•VFO A: 14.000.00 MHz/ USB
•VFO B: 14.000.00 MHz/ USB
The Memory channels and Quick Memory channels have no data stored.
9)25(6(7
Perform a VFO Reset if a key or control does not function according to the instructions in this manual. The following data is NOT erased by performing a VFO Reset.
•Memory channel data
•Menu settings
•Antenna tuner preset data
•ANT 1/ ANT 2 selection data
•Frequency and mode data for the Auto Mode function
•Various adjustment setting values
1Turn the transceiver power OFF.
2Press [A/B (A=B)] + [
] to switch the transceiver ON.
• A confirmation message appears on the display.
3Turn the MULTI/CH control and select “VFO RESET”.
)8//5(6(7
Perform a Full Reset if you want to erase all the data in all the memory channels. In addition, this function resets all the settings that you customized, to the factory defaults (i.e.- menu settings, antenna tuner preset data, etc.).
1Turn the transceiver power OFF.
2Press [A/B (A=B)] + [
] to switch the transceiver ON.
• A confirmation message appears on the display.
3Turn the MULTI/CH control and select “FULL RESET”.
4Press [A/B (A=B)] to perform the Full reset.
•A confirmation message appears when performing the Full Reset. Press [A/B (A=B)] again to proceed. Otherwise, press any other key to cancel the Partial Reset and return to normal operation.
•All frequencies, modes, memory data, adjustment values, and AT preset data are set to the factory default values.
78