Specifications
Default Settings and Ranges (viewed in MATE)
Table 17 12-Volt Inverter Settings (MATE)
Field
Item
Default
Minimum
Maximum
| search sensitivity (see page 14 for increments) | 6 | 0 |
| 50 |
Search | search pulse length | 8 | 4 |
| 20 |
| search pulse spacing | 60 AC cycles | 4 AC cycles |
| 120 AC cycles |
| ac transfer control | Grid |
| Grid or Gen | |
Input | ac1/grid limit | 25 Aac | 2.5 Aac |
| 30 Aac |
| ac2/gen limit | 25 Aac | 2.5 Aac |
| 30 Aac |
| low battery | 10.5 Vdc | 9 Vdc |
| 12 Vdc |
Inverter | low battery | 12.5 Vdc | 10 Vdc |
| 14 Vdc |
| adjust output voltage | 230 Vac | 210 Vac |
| 250 Vac |
| charger limit | 5 Aac | 0 Aac |
| 6 Aac |
| absorb voltage | 14.4 Vdc | 13 Vdc |
| 16 Vdc |
| absorb time limit | 1.0 hours | 0.0 hours |
| 24.0 hours |
Charger | float voltage | 13.6 Vdc | 12 Vdc |
| 15 Vdc |
float time period | 1.0 hours | 0.0 hours |
| 24.0 hours | |
|
| ||||
| refloat voltage | 12.5 Vdc | 12 Vdc |
| 13 Vdc |
| equalization voltage | 14.6 Vdc | 14 Vdc |
| 17 Vdc |
| equalization time period | 1.0 hours | 0.0 hours |
| 24.0 hours |
| ac1/grid lower limit | 208 Vac | 140 Vac |
| 220 Vac |
Grid | ac1/grid upper limit | 252 Vac | 250 Vac |
| 280 Vac |
ac1/grid input limit | 25 Aac | 2.5 Aac |
| 30 Aac | |
|
| ||||
| ac1/grid transfer delay | 6 AC cycles | 0 AC cycles |
| 240 AC cycles |
| gen input connect delay | 0.5 minutes | 0.2 minutes |
| 15 minutes |
Generator | ac2/gen lower limit | 208 Vac | 140 Vac |
| 220 Vac |
ac2/gen upper limit | 252 Vac | 250 Vac |
| 280 Vac | |
(Gen) | ac2/gen input limit | 25 Aac | 2.5 Aac |
| 30 Aac |
| ac2/gen transfer delay | 6 AC cycles | 0 AC cycles |
| 240 AC cycles |
| ac2/gen support | ON |
| ON or OFF | |
| aux output control | AUTO | ON, OFF, or AUTO | ||
| aux output function | Cool Fan | Cool Fan, DivertDC, DivertAC, AC Drop, Vent | ||
|
| Fan, Fault, GenAlert, LoadShed, or Remote | |||
|
|
| |||
| genalert on voltage | 11 Vdc | 10 Vdc |
| 14 Vdc |
Auxiliary | genalert on delay | 4 minutes | 0 minutes |
| 240 minutes |
genalert off set point | 14 Vdc | 12 Vdc |
| 18 Vdc | |
(AUX) | genalert off delay | 9 minutes | 0 minutes |
| 240 minutes |
| load shed off voltage | 11 Vdc | 10 Vdc |
| 14 Vdc |
| vent fan on set point | 13 Vdc | 10 Vdc |
| 16 Vdc |
| vent fan off period | 5 minutes | 0 minutes |
| 30 minutes |
| diversion on voltage | 14.6 Vdc | 12 Vdc |
| 16 Vdc |
| diversion off delay | 30 seconds | 0 seconds |
| 240 seconds |
Stacking | stack phase | Master | Master, OB Slave L1, 3p Classic B, 3p Classic C | ||
Power Save | master adjust only | 0 | 0 |
| 7 |
slave adjust only | 1 | 1 |
| 15 | |
|
| ||||
Sell | sell re volts | 13 Vdc | 10 Vdc |
| 15 Vdc |
grid tie window | User |
| IEEE or User | ||
| grid tie authority | GridTie | GridTie or No Sell | ||
Calibration | vac input adjustment1 | 236 | 220 |
| 254 |
vac output adjustment1 | 236 | 220 |
| 254 | |
(Cal) |
| ||||
battery vdc adjustment2 | 2 | 0 |
| 4 | |
|
| ||||
1These values are in digital counts, not volts. Lower counts stand for higher voltages, and higher counts mean lower voltages. One count equals approximately 1 Vac. The range of adjustment is 15 Vac above nominal and 17 Vac below nominal.
2These values are in digital counts, not volts. One count equals 0.1 Vdc. The range of adjustment is 0.2 Vdc above or below nominal.
47 |