Graco 3A1163A important safety instructions Fire and Explosion Hazard

Page 6

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

Use only grounded hoses.

Hold gun firmly to side of grounded pail when triggering into pail.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.

Connect only to grounded power source.

All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

INTRINSIC SAFETY

Intrinsically safe equipment that is installed improperly or connected to non-intrinsically safe equipment will create a hazardous condition and can cause fire, explosion, or electric shock. Follow local regulations and the following safety requirements.

Only models with a G3000, G250, G3000HR, G250HR, or intrinsically safe Coriolis meter are approved for installation in a Hazardous Location - Class I, Div I, Group D, T3 or Zone I Group IIA T3.

Do not install equipment approved only for a non-hazardous location in a hazardous area. See the ID label for the intrinsic safety rating of your model.

Do not substitute or modify system components as this may impair intrinsic safety.

6

3A1163A

Image 6
Contents ProControl 1KS II 2 GContents Related Manuals Equipment ApprovalsSystem Configuration and Part Numbers ModelsLabel Location on EasyKey Feature AccessoryFire and Explosion Hazard Skin Injection Hazard Toxic Fluid or Fumes Hazard Important Two-Component Material Information Component Identification and Definition Component Description Fluid Manifold FM Control Box Power Supply Cable PS Flow ControlAssembly FC Pneumatically Operated Dose Valve for component aLocation Requirements Intrinsically Safe Installation RequirementsLocation Optional CablesNON-HAZARDOUS Hazardous Classified Location Location only Requirements onSee Dimensions and Mounting Hole Layouts, General InformationWall Mounting ProControl 1KS System Layout Drawing Wall Mounting Requirements See the System Pneumatic Schematic onAir Supply Air ConnectionsFluid Supply Fluid ConnectionsColor Change Board and Solenoid Valves Color Change Valve Stack TI11668aRegulator Fluid Air Fluid Out FC Cable Flow Control RegulatorRequirements Connect Main Power ElectricalEasyKey Connections and AC Power Switch Connect EasyKey to Fluid Station ControlFluid Station Board Connections Color Change Board Switch Settings Two Color Change Boards Connect Color Change ModuleOne Color Change Board Switch S3-S6 J11 IG . Color Change Board Switches S3-S6Positions Wiring Diagram Grounding Check ResistanceEasyKey Display Control Box RobotSchematic Diagrams System Pneumatic SchematicSystem Electrical Schematic Non-Hazardous AreaHazardous Area Dimensions and Mounting Hole Layouts Wall Panel Mounting bracket onlyEasyKey Flow Control Module Air Supply ControlDimensions and Mounting Hole Layouts Technical Data Maximum fluid working pressure Maximum working air pressureGraco Standard Warranty Graco Information