Multiquip HHXG5 operation manual Specifications Engine, Fuel

Page 15

		SPECIFICATIONS (ENGINE)


	Table 2. HHXG5 Engine Specifications
	Model	Vanguard DM950G
	Type	Gasoline
	Cylinders	3
	Displacement	58.1 cu.in. (952 cc)
	Power (Maximum Output)	31 HP (23.1 kW) @3600 rpm
	Bore and Stroke	2.83 in. x 3.07 (72 mm x 78 mm)
	Maximum Torque (Intermittent)	70.0 Nm @ 2200 rpm
	Compression Ratio	8.7 : 1
	Cooling System	Fully jacketed water-cooled
	Engine Oil Capacity	3.2 qt. (3 liters)
	Engine Oil Capacity	3.5 qt. (3.3 liters) w/ oil filter
		replacement
	Lubricating System	Pressure feed with spin-on filter
	Fuel Tank	9 gal. (34 liters)
	Fuel Delivery System	Carbureted
	Helical Gearbox Gear	144 oz. (4.26 liters)
	Compound Capacity	ISO 22O AGMA GR 5EP

	Fuel	Gasoline - minimum of 87 octane
	Fuel	rating
		rating
	Starting System	Electric Starter
	Dry Weight	143.3 lbs. (65 Kg)
		17.4 in. x 17.1 in. x 19.7 in
	Dimensions (L x W x H)	(441.8 mm x 443.2 mm x 501.4
		mm).

HHXG5 RIDE-ON TROWEL • operation manual — rev. #1 (10/25/10) — page 15

Image 15

Contents Model HHXG5 Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningRespiratory Hazards HHXG5 Ride-On Trowel Table of ContentsPage Completely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTY meSSageS Safety InformationGeNeRaL SaFeTY Before servicing equipment TROWeL SaFeTYENgINe SaFeTY Order Form PT-160FueL SaFeTY BaTTeRY SaFeTY„ Use well-insulated gloves when picking up the battery „ aLWaYS shutdown engine before transporting TRaNSpORTINg SaFeTYTOWINg SaFeTY LiftingENvIRONmeNTaL SaFeTY HHX Specifications DIMENSIONS/SPECIFICATIONS TrowelFuel Specifications EngineGeneral Information HHXG5 Controls and Indicators Front Controls and IndicatorsHHXG5 Controls and Indicators Rear HHXG5 Controls and Indicators Clamshell Open Linked to the accelerator system Engine Components GasolineSetup Trowel Setup InstructionsBattery Setup Fuel InspectionEngine Oil Level Gearbox Oil LevelStarting the Engine OperationControl Joystick Directional Positioning SteeringMatching Blade Pitch for Both Sets of Blades Blade PitchMonthly 100-150 Hours MAINTENANCEMaintenance Schedule Daily 8-10 Hours Weekly 30-40 HoursFuel Filter Air Cleaner DailyChanging Engine Oil And Filter Oil Filter 300 HoursRadiator/Cooling System Battery/Charging SystemOil/Water Separator Oil And Fuel LinesMAINTENANCE old style clutch Checking The Drive BeltRemoving the Drive Belt Expanding Lower Drive Pulley Installing the Drive Belt Using New Drive BeltLeft Side Gearbox Spare Drive Belt ReplacementSprings High Engine RPM Driven Pulley How It Works FigureSpring Driven Pulley CAM Bracket Moveable Fixed Face ClutchBelt measurement MAINTENANCE new style clutchLower drive pulley Installing Drive BeltHow it works Twin PitchTM MAINTENANCE TrowelBlade Pitch Adjustment Procedure Single Pitch„„Do the pitch control towers rock back and forth? Steering AdjustmentClean-Up Changing BladesDistance from the lower wear plate Trowel Arm AdjustmentAssembly Place the trowel in a FLAT, Level areaTrowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NRe-Assembly Installing Pans Onto Finisher BladesLifting/Crush Hazard.DO not lift trowel with pans attached Move the throttle lever to Full engine RPM Checking Steering PressureHydraulic Steering Pressure Verify the hydraulic fluid level is correctSteering Pressure Check Steering Pressure AdjustmentDecommissioning Trowel/Components Decommissioning trowelStarter Wiring Diagram EngineConnector Orientation Front View Relay Orientation Symptom Possible problem Solution TroubleshootingTroubleshooting Ride-On Trowel Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner HERE’S HOW to GET Help

Related manuals

Manual 68 pages 56.17 Kb