Multiquip HHXG5 operation manual Decommissioning trowel, Decommissioning Trowel/Components

Page 45

decommissioning trowel

Decommissioning Trowel/Components

Decommissioning is a controlled process used to safely retire a piece of equipment that is no longer serviceable. If the equipment poses an unacceptable and unrepairable safety risk due to wear or damage or is no longer cost effective to maintain, (beyond life-cycle reliability) and is to be decommissioned, (demolition and dismantlement), the following procedure must take place:

1.Drain all fluids completely. These may include oil, gasoline, hydraulic oil and antifreeze. Dispose of properly in accordance with local and governmental regulations. Never pour on ground or dump down drains or sewers.

2.Remove battery and bring to appropriate facility for lead reclamation. Use safety precautions when handling batteries that contain sulfuric acid, (See “Safety Information” Section).

3.The remainder can be brought to a salvage yard or metal reclamation facility for further dismantling.

HHXG5 RIDE-ON TROWEL • operation manual — rev. #1 (10/25/10) — page 45

Image 45

Contents Model HHXG5 Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningRespiratory Hazards HHXG5 Ride-On Trowel Table of ContentsPage Completely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTY meSSageS Safety InformationGeNeRaL SaFeTY ENgINe SaFeTY TROWeL SaFeTYOrder Form PT-160 Before servicing equipmentFueL SaFeTY BaTTeRY SaFeTY„ Use well-insulated gloves when picking up the battery TOWINg SaFeTY TRaNSpORTINg SaFeTYLifting „ aLWaYS shutdown engine before transportingENvIRONmeNTaL SaFeTY HHX Specifications DIMENSIONS/SPECIFICATIONS TrowelFuel Specifications EngineGeneral Information HHXG5 Controls and Indicators Front Controls and IndicatorsHHXG5 Controls and Indicators Rear HHXG5 Controls and Indicators Clamshell Open Linked to the accelerator system Engine Components GasolineSetup Trowel Setup InstructionsBattery Setup Engine Oil Level InspectionGearbox Oil Level FuelStarting the Engine OperationControl Joystick Directional Positioning SteeringMatching Blade Pitch for Both Sets of Blades Blade PitchMaintenance Schedule Daily 8-10 Hours MAINTENANCEWeekly 30-40 Hours Monthly 100-150 HoursChanging Engine Oil And Filter Air Cleaner DailyOil Filter 300 Hours Fuel FilterOil/Water Separator Battery/Charging SystemOil And Fuel Lines Radiator/Cooling SystemMAINTENANCE old style clutch Checking The Drive BeltRemoving the Drive Belt Expanding Lower Drive Pulley Installing the Drive Belt Using New Drive BeltLeft Side Gearbox Spare Drive Belt ReplacementSprings High Engine RPM Driven Pulley How It Works FigureSpring Driven Pulley CAM Bracket Moveable Fixed Face ClutchBelt measurement MAINTENANCE new style clutchLower drive pulley Installing Drive BeltHow it works Blade Pitch Adjustment Procedure MAINTENANCE TrowelSingle Pitch Twin PitchTMClean-Up Steering AdjustmentChanging Blades „„Do the pitch control towers rock back and forth?Assembly Trowel Arm AdjustmentPlace the trowel in a FLAT, Level area Distance from the lower wear plateTrowel Blade Removal Trowel Arm RemovalRemove the trowel arm from the spider plate Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NRe-Assembly Installing Pans Onto Finisher BladesLifting/Crush Hazard.DO not lift trowel with pans attached Hydraulic Steering Pressure Checking Steering PressureVerify the hydraulic fluid level is correct Move the throttle lever to Full engine RPMSteering Pressure Check Steering Pressure AdjustmentDecommissioning Trowel/Components Decommissioning trowelStarter Wiring Diagram EngineConnector Orientation Front View Relay Orientation Symptom Possible problem Solution TroubleshootingTroubleshooting Ride-On Trowel Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner HERE’S HOW to GET Help

Related manuals

Manual 68 pages 56.17 Kb