Multiquip HHXG5 operation manual Installing Drive Belt, Lower drive pulley

Page 35

mAINTENANCE (new style clutch)

2. Disconnect the left-side CV Axle from the left-side gearbox and the lower drive pulley coupler. See Figure 30.

UPPER DRIVE

PULLEY/CLUTCH

	LOWER
	DRIVE
	PULLEY
CVT	CV AXLE
CVT
BELT	GEARBOX
	COUPLER
	COUPLER

LEFT-SIDE

GEARBOX

Figure 30. Remove Left-Side CV Axle

3.If the belt is not being reused (recommended), CUT the drive belt. Ensure all belt remnants are removed from the pulleys.

installing Drive Belt

1.Place new CVT belt over the lower pulley. Squeeze the belt (Figure 31) and pull the belt upwards and towards the rear of the trowel. This will spread open the faces

of the lower drive pulley.

CVT BELT (P/N 23365)

PULL UPWARDS

AND TOWARDS

REAR OF TROWEL

FIXED

FACE

MOVEABLE LOWER

FACE PULLEY

Figure 31. Holding Lower Pulley Open

2.Place free end of CVT belt into upper pulley grooves See Figure 32.

CLUTCH

UPPER

PULLEY

LOWER

PULLEY

Figure 32. Upper Pulley Belt Installation

3.Reconnect left-side CV Axle Assembly. to the left side gearbox and lower drive pulley coupler. See Figure 30.

HHXG5 RIDE-ON TROWEL • operation manual — rev. #1 (10/25/10) — page 35

Image 35

Contents Model HHXG5 Proposition 65 Warning Respiratory Hazards Silicosis/Respiratory WarningsSilicosis Warning HHXG5 Ride-On Trowel Table of ContentsPage Completely Training checklistDaily pre-Operation Checklist Daily pre-operation checklistSaFeTY meSSageS Safety InformationGeNeRaL SaFeTY Before servicing equipment TROWeL SaFeTYENgINe SaFeTY Order Form PT-160„ Use well-insulated gloves when picking up the battery FueL SaFeTYBaTTeRY SaFeTY „ aLWaYS shutdown engine before transporting TRaNSpORTINg SaFeTYTOWINg SaFeTY LiftingENvIRONmeNTaL SaFeTY HHX Specifications DIMENSIONS/SPECIFICATIONS TrowelFuel Specifications EngineGeneral Information HHXG5 Controls and Indicators Front Controls and IndicatorsHHXG5 Controls and Indicators Rear HHXG5 Controls and Indicators Clamshell Open Linked to the accelerator system Engine Components GasolineBattery Setup SetupTrowel Setup Instructions Fuel InspectionEngine Oil Level Gearbox Oil LevelStarting the Engine OperationControl Joystick Directional Positioning SteeringMatching Blade Pitch for Both Sets of Blades Blade PitchMonthly 100-150 Hours MAINTENANCEMaintenance Schedule Daily 8-10 Hours Weekly 30-40 HoursFuel Filter Air Cleaner DailyChanging Engine Oil And Filter Oil Filter 300 HoursRadiator/Cooling System Battery/Charging SystemOil/Water Separator Oil And Fuel LinesRemoving the Drive Belt MAINTENANCE old style clutchChecking The Drive Belt Expanding Lower Drive Pulley Installing the Drive Belt Using New Drive BeltLeft Side Gearbox Spare Drive Belt ReplacementSprings High Engine RPM Driven Pulley How It Works FigureSpring Driven Pulley CAM Bracket Moveable Fixed Face ClutchBelt measurement MAINTENANCE new style clutchLower drive pulley Installing Drive BeltHow it works Twin PitchTM MAINTENANCE TrowelBlade Pitch Adjustment Procedure Single Pitch„„Do the pitch control towers rock back and forth? Steering AdjustmentClean-Up Changing BladesDistance from the lower wear plate Trowel Arm AdjustmentAssembly Place the trowel in a FLAT, Level areaRemove the trowel arm from the spider plate Trowel Blade RemovalTrowel Arm Removal Checking Trowel Arm Straightness Locate the trowel arm adjustment tool P/NLifting/Crush Hazard.DO not lift trowel with pans attached Re-AssemblyInstalling Pans Onto Finisher Blades Move the throttle lever to Full engine RPM Checking Steering PressureHydraulic Steering Pressure Verify the hydraulic fluid level is correctSteering Pressure Check Steering Pressure AdjustmentDecommissioning Trowel/Components Decommissioning trowelStarter Wiring Diagram EngineConnector Orientation Front View Relay Orientation Symptom Possible problem Solution TroubleshootingTroubleshooting Ride-On Trowel Troubleshooting engine Air cleaner dirty? Clean or replace air cleaner HERE’S HOW to GET Help

Related manuals

Manual 68 pages 56.17 Kb