Furuno FSV-30S installation manual Signal cable 10S2240 connects to Junction BOX display side

Page 37

3.Lead in cable thru the appropriate location on the cable clamp and fix cable with appropriate CKS clamp. Connect each cable to circuit board as shown in the figure on the previous page.

Signal cable (10S2240) connects to “JUNCTION BOX” display side.

4.Lay the shield of each cable in the cable clamp.

5.Fasten the cable clamps.

2-15

Image 37

Contents Color Scanning Sonar 00014857415 Safety Instructions Projected Raising Lowering Mm stroke Max kt Iii System ConfigurationOptional Equipment Standard supplyMounting considerations Hull UnitHull unit mounting location Maintenance space, example sonar compartment Guidelines for shortening the retraction tank Shortening the retraction tankHow to install reinforcement ribs Remarks for installation of retraction tankInstalling hull unit on retraction tank Installation of hull unit Proper installation of stays Installing stays anti-vibration measureProper and improper stay installation methods Mounting considerations Processor UnitProcessor unit, rear view Control Unit Mounting procedureProcessor unit Rubber feetMounting without KB fixing plate How to attach KB fixing plateControl unit Mounting with KB fixing plateControl unit, side view Control unit, cover removedGrounding the Equipment Transceiver UnitTransceiver unit Transceiver unit, junction box Use copper strap suppliedProcedure Installing the Attachment Flange optionAttachment flange Type OP10-27, Code no Junction box Cable Extension Kit optionAttachment kit Type OP10-24, Code no Installing the Attachment Kit optionInstallation of attachment kit How to use the crimping tool How to Use the Crimping Tool, Pin ExtractorHow to use the pin extractor Crimping tool, contact pin, pin extractorWiring WiringTransceiver unit side Cable type 10S1258-1, sectional view 1 10S1258-1 cableFabrication of cable for connector 00-8016-038-313761HV Fabrication of connector 00-8016-038-313761HV CN-A101Assembling 38P connector Positioning guide pinsAssembling connector NCS-253-P Power cableControl cable Sectional view of cables Cable listGyro Synchronizing with echo sounder or other sonar Menu settingFor current driven KP input For voltage driven KP 12 V inputFabrication of cable for 00-8016-038-313761HV Fabrication of connector 00-8016-038-313761HV CN-B101CN-B101 CN-B102 Transceiver unit, inside viewHull control cable 10S2078 Fabrication of power cable type DPYCYS-2.5 TB-B101Fabrication of cable type DPYCYS-2.5 Transceiver unit, top view Wiring in transceiver unitJunction box Cable Extension KitJunction box, cover removed Signal cable 10S2240 connects to Junction BOX display side Raise/lower control box, cover removed Raise/Lower control boxPower cable fabrication Input voltage Input Voltage and FusesFuses Marking the labelMain menu Hull Unit CheckOthers menu Test menu Initial Setting menuTransducer switches of the control unit How to check the hull unitControl unit in hull unit Page Heading adjustment Heading AdjustmentSystem menu Others menu, Heading Adjust OWN Ship Mark menu, setting window Configuring Own Ship MarkOWN Ship Mark menu Ship shape description Interface Setting menu Interface Setting menuOther System Menu Items EXT Data Setting menu EXT Data Setting menuData sentences Nmea 0183, Furuno proprietary ES Draft Offset Others menuAdjustment of signal level echo sounder connected Cone Board Setting in the Processor UnitAdjusting the volume of the audio alarm 1 CIF2/NMEA2 connector interface selection DIP Switch SettingProcessor unit, inside view Ifes Board 10P6983Choosing echosounder signal This page intentionally left blank Processor unit, front view Name Type Code No Qty RemarksGND Wiring between processor unit and CS-120ADcon Board 10P6984 or 10P6984A This page intentionally left blank ＰａｃｋｉｎｇＬｉｓｔ FSV-301 58 58 585858 付属品表 52#42#465.+5614 52 Page Page Page Hatai Hatai Hatai Hatai Hatai Page Page This page is intentionally left blank Color Scanning Sonar Miyosi