Furuno FSV-30S installation manual Dcon Board 10P6984 or 10P6984A

Page 59

8. Set the DIP switch on the DCON Board as follows.

Input port

DIP switch setting on DCON Board

CIF1

S3-#2: ON

NMEA 2/CIF 2

S3-#3: ON

S3

DCON Board (10P6984 or 10P6984A)

Note: If the CIF1 format is selected, change baud rate to 2400 bps. See CIF BAUD RATE on page 3-9 for details.

4-3

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Color Scanning Sonar 00014857415 Safety Instructions Projected Raising Lowering Mm stroke Max kt Iii System ConfigurationOptional Equipment Standard supplyHull unit mounting location Hull UnitMounting considerations Maintenance space, example sonar compartment Guidelines for shortening the retraction tank Shortening the retraction tankHow to install reinforcement ribs Remarks for installation of retraction tankInstalling hull unit on retraction tank Installation of hull unit Proper and improper stay installation methods Installing stays anti-vibration measureProper installation of stays Processor unit, rear view Processor UnitMounting considerations Rubber feet Mounting procedureControl Unit Processor unitMounting with KB fixing plate How to attach KB fixing plateMounting without KB fixing plate Control unitControl unit, side view Control unit, cover removedTransceiver unit, junction box Use copper strap supplied Transceiver UnitGrounding the Equipment Transceiver unitAttachment flange Type OP10-27, Code no Installing the Attachment Flange optionProcedure Junction box Cable Extension Kit optionAttachment kit Type OP10-24, Code no Installing the Attachment Kit optionInstallation of attachment kit Crimping tool, contact pin, pin extractor How to Use the Crimping Tool, Pin ExtractorHow to use the crimping tool How to use the pin extractorWiring WiringTransceiver unit side Cable type 10S1258-1, sectional view 1 10S1258-1 cablePositioning guide pins Fabrication of connector 00-8016-038-313761HV CN-A101Fabrication of cable for connector 00-8016-038-313761HV Assembling 38P connectorControl cable Power cableAssembling connector NCS-253-P Sectional view of cables Cable listGyro For voltage driven KP 12 V input Menu settingSynchronizing with echo sounder or other sonar For current driven KP inputFabrication of cable for 00-8016-038-313761HV Fabrication of connector 00-8016-038-313761HV CN-B101CN-B101 CN-B102 Transceiver unit, inside viewFabrication of cable type DPYCYS-2.5 Fabrication of power cable type DPYCYS-2.5 TB-B101Hull control cable 10S2078 Transceiver unit, top view Wiring in transceiver unitJunction box, cover removed Cable Extension KitJunction box Signal cable 10S2240 connects to Junction BOX display side Raise/lower control box, cover removed Raise/Lower control boxPower cable fabrication Marking the label Input Voltage and FusesInput voltage FusesOthers menu Hull Unit CheckMain menu Test menu Initial Setting menuControl unit in hull unit How to check the hull unitTransducer switches of the control unit Page System menu Heading AdjustmentHeading adjustment Others menu, Heading Adjust OWN Ship Mark menu Configuring Own Ship MarkOWN Ship Mark menu, setting window Ship shape description Other System Menu Items Interface Setting menuInterface Setting menu EXT Data Setting menu EXT Data Setting menuData sentences Nmea 0183, Furuno proprietary ES Draft Offset Others menuAdjusting the volume of the audio alarm Cone Board Setting in the Processor UnitAdjustment of signal level echo sounder connected Ifes Board 10P6983 DIP Switch Setting1 CIF2/NMEA2 connector interface selection Processor unit, inside viewChoosing echosounder signal This page intentionally left blank Processor unit, front view Name Type Code No Qty RemarksGND Wiring between processor unit and CS-120ADcon Board 10P6984 or 10P6984A This page intentionally left blank Ｐａｃｋｉｎｇ Ｌｉｓｔ FSV-301 58 58 58 58 58 付属品表 52#42#465.+5614 52 Page Page Page Hatai Hatai Hatai Hatai Hatai Page Page This page is intentionally left blank Color Scanning Sonar Miyosi
Top Page Image Contents