Furuno CH300 manual Setting of Motion Sensor/Satellite Compass, Adj motion sensor menu

Page 48

3. ADJUSTMENT

3.6Setting of Motion Sensor/Satellite Compass

When connecting the motion sensor, clinometer or satellite compass, enter ship’s roll and pitch angles as shown below. Note that the adjustment can be done only when connected to the MOTION SENSOR port. For the satellite compass, however, do not duplicate this adjustment; enter values at one location only.

1.Press the MENU key to display the user menu.

2.Press to ► select SYS at the top of the menu display.

3.Press ▼ to select GO TO SYS.

4.Press ◄ to select YES.

5.Press ▼ to select ADJ MOTION SENSOR, and then press ► to display the ADJ MOTION SENSOR menu.

**ADJ MOTION SENSOR **

ROLL ANGLE:

 

ADJ:

 

+5*

˚

(-10˚ - +10˚)

 

 

 

 

 

 

 

 

PITCH ANGLE:

ADJ:

+5*

˚

(-10˚ - +10˚)

: SELECT

: CHANGE

MENU: END

*: For Clinometer BS-704, tilt angle is displayed. For Motion Sensor MS-100,

the readout is "0" (zero) when the ship is stopped, regardress of actual roll or pitch.

Adj motion sensor menu

6.Press ▲ or ▼ to select ROLL ANGLE or PITCH ANGLE.

7.Press ◄ or ► to adjust (-10°to +10°).

8.For MS-100, use a clinometer or other similar measuring device to measure ship’s semi-permanent inclination angle. Take the polarity of the angle. For example, if the stern is 3° down, set -3°.

+

0

 

+

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

 

 

 

-

 

 

 

 

 

 

ROLL ANGLE

 

Starboard up

 

 

Starboard down

 

 

 

 

 

 

PITCH ANGLE

 

Stern up

 

 

Stern down

 

 

 

 

 

 

 

 

 

For clinometer BS-704, adjust so that the indication shows “0” (zero).

9. Press the MENU key several times to close the menu.

3-8

Image 48
Contents DUAL-FREQUENCY Searchlight Sonar 00015190211 Safety Instructions Working with the Sonaroil Table of Contents System Configuration Equipment Lists Standard SupplyOptions Monitor Unit/Control Unit Mounting baseBracket, rear view Fastening bracket to mounting baseMounting separated monitor unit Bracket rear view Control Unit Blackbox typeHex. bolts Fixing metal Transceiver Unit Transceiver unitInstallation location for hull unit Hull UnitTransducer tank Assembling and mounting of hull unit Shaft sleeve and raise/lower drive unit assembly Trunnion pinApplying Cemedine High Super to main shaft Tank and tank guide, sectional viewInstalling shims 1800 1600 1400 1200 Tank guide attachment Installing grease cotton on the main shaft Detaching the soundome Filling the soundome with sonar oilEmergency Paint area Mounting Checking manual raise/lower of soundome with hand crank Interface Unit Motion Sensor MS-100 option Mounting considerationsClinometer BS-704 option Wiring Wiring Among UnitsWiring, with monitor WiringWiring, without monitor MJ-A6SPF DPYCYS-2.5TB1 Transceiver unit, internal viewConnection of transceiver unit to other sonar/echo sounder Outputting KP of CH-300 to other sonar, echo sounderHull unit, inside view VGA NAV I/O Sentences Available I/O sentencesGeneral Checks General checksChecking TX Frequency General checks con’tUser menu SYS System menu Test displayHeading Alignment Setting Checking heading alignmentHeading offset display Setting for Synchronizing Transmission with other Equipment Menu COM1TX Rate window Setting for Satellite Compass System setting 1 menuSystem setting 2 menu Setting of Motion Sensor/Satellite Compass Adj motion sensor menuSystem backup menu System Back UpSetting of Interface Unit Interface unit, DIP switch S1 location+/05+105+0&4#9+014440%10. +/05+105+0&4#9+014440%10.#8 #%%5514+5 㩖㩡㩧㩆㩨 #8 Page Page Page Page Page Page Page Hatai This page is intentionally left blank Page Page Page Page Page Page Page Hatai Page This page is intentionally left blank Page Page Page Page Page 2周波サーチライトソナー 2周波サーチライトソナーI/Fユニット使用