Raymarine 420D manual Controlling the display, Selecting the display mode

Page 23

2-4							RayChart 420/420D Chartplotter

2.Press trackpad left/right to highlight SYSTEM SET UP and press ENTER to display the System Set Up menu.

3.Use trackpad up/down to highlight the SIMULATOR option .

4.Use trackpad left/right to select ON.

5.If necessary, use trackpad up/down to highlight, in turn, the SIMULATED SOG and COG options and trackpad left/right to set as required . These set Speed in 1Kt intervals and Course in 1° intervals, respectively.

6.Press CLEAR twice to return to the chart screen.

2.4Controlling the display

This section describes how to:

•Change the display mode.

•Move around the chart by panning the display, changing the chart centre and changing the chart scale.

Selecting the display mode

Use the PAGE key to select the display mode. Select the following modes by repeat presses of the PAGE key as listed below and shown in the following illustration:

•Set Up functions (see Chapter 4)

•Course Deviation Indicator (CDI)

•Bearing & Distance Indication (BDI)

•Waypoint data

•Navigation data

•Time/Date data

•Return to Set Up functions

Note: Press GOTO to return to normal Chart display at any time.

Image 23

Contents Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s HandbookUnited States EMC Conformance WarrantyPreface RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D How this Handbook is organised OverviewIntroduction Display functions Chartplotter displayGeneral Display options Operating controls128 nm Trackpad and cursorFunction bar Dedicated keysDatabase lists Pop-up menusSimulator Getting startedConventions used Switching on/off Chart simulator Controlling the display Selecting the display modeTime 1234 Date 26/01/99 Using Find Ship Moving around the chartStatus Bar Chart range Changing the chart scale128 nm Using Navionics Nav-Chart cardsInserting a Nav-Chart card Displaying chart information Removing a Nav-Chart cardDisplaying the chart data To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypointsPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypointWorking with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screenEditing a route Displaying route leg and waypoint informationErasing or renaming a route To add a waypoint to the end of a route Inserting/deleting waypoints in a routeFollowing routes and going to target points Reverse a route Follow a routeJoin a route Target point arrivalAlter a route Advance to a waypoint Restart Cross Track Error XTEGo to a waypoint Going to an individual targetGo to a port Go to cursorStop follow or stop goto Changing the display modeCDI display BDI display Waypoint data BRG 234 T RNG 12.4 nmNavigation data COG 230 T SOG 6.8 KtsTime/Date Data Time Date 26/01/99Managing database lists Transferring waypoints and routesDisplayed waypoints WPT/ROUTE Transfer Using tracksSetting Setting up a trackSmartRoute‰ Man Overboard MOBClearing the current track Range key operates normally to change chart scale AlarmsSystem set up parameters Setting up the chartplotterMenu Options Factory New Default Setting Variation Bearing modeKey beep UnitsSimulated COG Time offsetLanguage Simulated SOGChart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol OrientationScreen amplifier Anchor alarmXTE alarm Chart textDepth contours 20M Chart boundariesDepth contours 5M Depth contours 10MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines InstallationConnections to other equipment Unpacking and inspecting the componentsSuppression ferrites Selecting the best location LocationItems Missing? Registering this Product122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mountingD47221 Cabling Chartplotter connectorsGPS connector POWER/NMEA connector Function Color System Check and Initial Switch OnSystem Check Initial Switch OnChecking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and SafetyTwo types of reset are available for the Chartplotter Resetting the systemFault finding Problem solvingWorldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and serviceHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a SpecificationRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviationsRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty CertificateUnited States of America Factory Service Centers