Raymarine 420D manual Inserting a Nav-Chart card

Page 28

Chapter 2: Getting Started	2-9

The chart scale in use is indicated in the status bar; the number represents the distance (in nautical miles) displayed from the top to the bottom of the screen.

To obtain Navionics Nav-Chart cards contact your local dealer or:

Navionics S.p.A. Via Vespucci 289 55049Viareggio, Italy

Tel: (+39) 584 961696

Fax: (+39) 584 961309

website: www.navionics.com

Inserting a Nav-Chart card

CAUTION

To prevent the ingress of water and consequent damage to the unit, always ensure that the cartridge cover is fully and properly inserted, whether or not a Nav-Chart card is inserted.

To insert a Nav-Chart card:

‰1. Check that you are using the correct Nav-Chart card for the required area.

2.Pull out the cartridge cover at the right hand side of the unit.

3.Hold the card with the title label and keyway slot towards you, and the two circular holes outermost, as shown below. Gently push the card into its slot until it clicks into position. It will only fit in the correct orientation.

4.To prevent the ingress of water, replace the cartridge cover.

D4706_1

Image 28

Contents Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety NoticesUnited States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display optionsTrackpad and cursor 128 nmDedicated keys Function barPop-up menus Database listsConventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the displayTime 1234 Date 26/01/99 Moving around the chart Using Find ShipChanging the chart scale Status Bar Chart rangeUsing Navionics Nav-Chart cards 128 nmInserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Safety OperationWorking with waypoints IntroductionPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypointWorking with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the databaseErasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a routeFollowing routes and going to target points Follow a route Reverse a routeAlter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypointGoing to an individual target Go to a waypointGo to cursor Go to a portChanging the display mode Stop follow or stop gotoCDI display BDI display BRG 234 T RNG 12.4 nm Waypoint dataCOG 230 T SOG 6.8 Kts Navigation dataTime Date 26/01/99 Time/Date DataDisplayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE TransferSetting up a track SettingClearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scaleSetting up the chartplotter System set up parametersMenu Options Factory New Default Setting Bearing mode Key beepUnits VariationTime offset LanguageSimulated SOG Simulated COGChart set up parameters Parameter Options Factory New Default Setting Plotter mode Waypoint symbolOrientation Show waypointsAnchor alarm XTE alarmChart text Screen amplifierChart boundaries Depth contours 5MDepth contours 10M Depth contours 20MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation GuidelinesSuppression ferrites Unpacking and inspecting the componentsConnections to other equipment Location Items Missing?Registering this Product Selecting the best location122 mm 4.8 Connecting to other equipment Mounting the chartplotterTrunnion yoke mounting Panel mountingD47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function ColorInitial Switch On System CheckChecking the Chartplotter Operation RayChart 420/420D Chartplotter Maintenance & fault finding MaintenanceServicing and Safety Routine checksResetting the system Two types of reset are available for the ChartplotterProblem solving Fault findingHow to contact Raytheon Marine US For accessories and partsFor product repair and service Worldwide supportHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2KRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COGRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty LimitationsFactory Service Centers United States of America