Raymarine 420D Connecting to other equipment, Mounting the chartplotter, Trunnion yoke mounting

Page 78

Chapter 5: Installation	5-5

5.4 Connecting to other equipment

The unit transmits navigation and waypoint data on NMEA and, therefore, can be connected to an NMEA(1) compatible autopilot or compatible instrument repeater(s). The navigation data transmitted by the chartplotter is detailed in Appendix B to this handbook.

(1)	National Marine Electronics Association (NMEA) 0183 interconnection

	standard, Version 2.3 April 1998.

5.5 Mounting the chartplotter

Trunnion (yoke) mounting

The display unit can be conveniently mounted on a dash area, chart table, bulkhead or deckhead, as shown in the following diagram.

1.Loosen the trunnion knobs and remove the trunnion from the display unit.

2.Mark the locations of the trunnion screw holes on the mounting surface.

3.Use the screws supplied to fix the trunnion at the marked locations.

4.Fit the unit to the trunnion, adjust the display angle and tighten the knobs.

5.Connect the Power/NMEA and GPS cables to the unit, avoiding tight bends in the cables.

Panel mounting

CAUTION:

Make sure that there are no hidden electrical wires or other items behind the location before proceeding. Make sure that there is sufficient rear access for mounting and cabling. Allow at least 4cm at the right hand side of the display to enable chart cards to be inserted and removed.

Image 78

Contents Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety NoticesUnited States Warranty PrefaceEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Overview IntroductionHow this Handbook is organised Chartplotter display GeneralDisplay functions Operating controls Display optionsTrackpad and cursor 128 nmDedicated keys Function barPop-up menus Database listsGetting started Conventions usedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the displayTime 1234 Date 26/01/99 Moving around the chart Using Find ShipChanging the chart scale Status Bar Chart rangeUsing Navionics Nav-Chart cards 128 nmInserting a Nav-Chart card Removing a Nav-Chart card Displaying the chart dataDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Working with waypoints SafetyOperation IntroductionPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypointWorking with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the databaseDisplaying route leg and waypoint information Erasing or renaming a routeEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a routeFollowing routes and going to target points Follow a route Reverse a routeTarget point arrival Alter a routeJoin a route Restart Cross Track Error XTE Advance to a waypointGoing to an individual target Go to a waypointGo to cursor Go to a portChanging the display mode Stop follow or stop gotoCDI display BDI display BRG 234 T RNG 12.4 nm Waypoint dataCOG 230 T SOG 6.8 Kts Navigation dataTime Date 26/01/99 Time/Date DataTransferring waypoints and routes Displayed waypointsManaging database lists Using tracks WPT/ROUTE TransferSetting up a track SettingMan Overboard MOB Clearing the current trackSmartRoute‰ Alarms Range key operates normally to change chart scaleSetting up the chartplotter System set up parametersMenu Options Factory New Default Setting Units Bearing modeKey beep VariationSimulated SOG Time offsetLanguage Simulated COGChart set up parameters Parameter Options Factory New Default Setting Orientation Plotter modeWaypoint symbol Show waypointsChart text Anchor alarmXTE alarm Screen amplifierDepth contours 10M Chart boundariesDepth contours 5M Depth contours 20MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation GuidelinesUnpacking and inspecting the components Suppression ferritesConnections to other equipment Registering this Product LocationItems Missing? Selecting the best location122 mm 4.8 Trunnion yoke mounting Connecting to other equipmentMounting the chartplotter Panel mountingD47221 Chartplotter connectors GPS connectorCabling POWER/NMEA connector System Check and Initial Switch On Function ColorInitial Switch On System CheckChecking the Chartplotter Operation RayChart 420/420D Chartplotter Servicing and Safety Maintenance & fault findingMaintenance Routine checksResetting the system Two types of reset are available for the ChartplotterProblem solving Fault findingFor product repair and service How to contact Raytheon Marine USFor accessories and parts Worldwide supportHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2KRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COGRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty LimitationsFactory Service Centers United States of America