Raymarine 420D manual Using tracks, WPT/ROUTE Transfer

Page 58

Chapter 3: Operation	3-27

7. To stop waypoint transfer, press ENTER.

To receive waypoints and route lists:

‰1. Display the Waypoint List as previously described, then select

WPT/ROUTE TRANSFER.

2. Select RECEIVE WAYPOINTS and press ENTER; the text changes to STOP RECEIVING and remains selected.

3. Initiate sending waypoints on the NMEA compatible equipment.

4. To stop waypoint transfer, press ENTER.

Note: If either the Waypoint List or Route List becomes full, a warning is displayed and the operation is terminated.

3.7 Using tracks

The Track function is used to mark an on-screen trail that your vessel has followed, as if it had left a visible fixed wake.

While the track is turned on, it is recorded in the display unit’s memory. You specify the interval at which track points are made and a line is drawn on-screen between each point. Up to 2000 track points can be saved in total.

The track remains on-screen, even following a Power off/on, until you clear the track.

Using the SmartRoute function, a track can also be converted to and saved as a route which is automatically reversed, ready for use as your return voyage.

This section describes how to:

•Set up a track and specify the interval between track points.

•Clear the current track.

•Convert the track to a route (SmartRoute).

To access the track controls:

‰1. From chart mode, press the PAGE key to display the chart set up function bar:

2.Select TRACK SET UP to display the Track function bar:

Image 58

Contents Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety NoticesUnited States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display optionsTrackpad and cursor 128 nmDedicated keys Function barPop-up menus Database listsConventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the displayTime 1234 Date 26/01/99 Moving around the chart Using Find ShipChanging the chart scale Status Bar Chart rangeUsing Navionics Nav-Chart cards 128 nmInserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Working with waypoints SafetyOperation IntroductionPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypointWorking with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the databaseErasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a routeFollowing routes and going to target points Follow a route Reverse a routeAlter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypointGoing to an individual target Go to a waypointGo to cursor Go to a portChanging the display mode Stop follow or stop gotoCDI display BDI display BRG 234 T RNG 12.4 nm Waypoint dataCOG 230 T SOG 6.8 Kts Navigation dataTime Date 26/01/99 Time/Date DataDisplayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE TransferSetting up a track SettingClearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scaleSetting up the chartplotter System set up parametersMenu Options Factory New Default Setting Units Bearing modeKey beep VariationSimulated SOG Time offsetLanguage Simulated COGChart set up parameters Parameter Options Factory New Default Setting Orientation Plotter modeWaypoint symbol Show waypointsChart text Anchor alarmXTE alarm Screen amplifierDepth contours 10M Chart boundariesDepth contours 5M Depth contours 20MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation GuidelinesSuppression ferrites Unpacking and inspecting the componentsConnections to other equipment Registering this Product LocationItems Missing? Selecting the best location122 mm 4.8 Trunnion yoke mounting Connecting to other equipmentMounting the chartplotter Panel mountingD47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function ColorInitial Switch On System CheckChecking the Chartplotter Operation RayChart 420/420D Chartplotter Servicing and Safety Maintenance & fault findingMaintenance Routine checksResetting the system Two types of reset are available for the ChartplotterProblem solving Fault findingFor product repair and service How to contact Raytheon Marine USFor accessories and parts Worldwide supportHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2KRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COGRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty LimitationsFactory Service Centers United States of America