Raymarine 420D manual Limited Warranty Certificate, Warranty Limitations

Page 100

Limited Warranty Certificate

Raytheon Marine Company warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below.

Defects will be corrected by Raytheon Marine Company or an authorized Raytheon dealer. Raytheon Marine Company will, except as provided below, accept labor cost for a period of 2 years/24 months from the date of sale to end user. During this period, except for certain products, travel costs (auto mileage and tolls) up to 100 round trip highway miles and travel time of 2 hours, will be assumed by Raytheon Marine Company only on products where proof of installation or commission by authorised service agents, can be shown.

Warranty Limitations

Raytheon Marine Company Warranty policy does not apply to equipment which has been subjected to accident, abuse or misuse, shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or equipment on which the serial number has been altered, mutilated or removed.

Except where Raytheon Marine Company or its authorized dealer has performed the installation, it assumes no responsibility for damage incurred during installation.

This Warranty does not cover routine system checkouts or alignment/calibration, unless required by replacement of part(s) in the area being aligned.

A suitable proof of purchase, showing date, place, and serial number must be made available to Raytheon Marine Company or authorized service agent at the time of request for Warranty service.

Consumable items, (such as: Chart paper, lamps, fuses, batteries, styli, stylus/drive belts, radar mixer crystals/ diodes, snap-in impeller carriers, impellers, impeller bearings, and impeller shaft) are specifically excluded from this Warranty.

Magnetrons, Cathode Ray Tubes (CRT), hailer horns and transducers are warranted for 1 year/12 months from date of sale. These items must be returned to a Raytheon Marine Company facility.

All costs associated with transducer replacement, other than the cost of the transducer itself, are specifically excluded from this Warranty.

Overtime premium labor portion of services outside of normal working hours is not covered by this Warranty.

Travel cost allowance on certain products with a suggested retail price below $2500.00 is not authorized. When/ or if repairs are necessary, these products must be forwarded to a Raytheon Marine Company facility or an authorized dealer at owner’s expense will be returned via surface carrier at no cost to the owner.

Travel costs other than auto mileage, tolls and two (2) hours travel time, are specifically excluded on all products. Travel costs which are excluded from the coverage of this Warranty include but are not limited to: taxi, launch fees, aircraft rental, subsistence, customs, shipping and communication charges etc..

Travel costs, mileage and time, in excess to that allowed must have prior approval in writing.

TO THE EXTENT CONSISTENT WITH STATE AND FEDERAL LAW:

(1)THIS WARRANTY IS STRICTLY LIMITED TO THE TERMS INDICATED HEREIN, AND NO OTHER WARRANTIES OR REMEDIES SHALL BE BINDING ON RAYTHEON MARINE COMPANY INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABLE OR FITNESS FOR A PARTICULAR PURPOSE.

(2)Raytheon Marine Company shall not be liable for any incidental, consequential or special (including punitive or multiple) damages.

All Raytheon Marine Company products sold or provided hereunder are merely aids to navigation. It is the responsibility of the user to exercise discretion and proper navigational skill independent of any Raytheon equipment.

44592-5 October 1999

Page 99 Page 101
Image 100
Page 99 Page 101
Contents Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety NoticesUnited States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display optionsTrackpad and cursor 128 nmDedicated keys Function barPop-up menus Database listsConventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the displayTime 1234 Date 26/01/99 Moving around the chart Using Find ShipChanging the chart scale Status Bar Chart rangeUsing Navionics Nav-Chart cards 128 nmInserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Safety OperationWorking with waypoints IntroductionPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypointWorking with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the databaseErasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a routeFollowing routes and going to target points Follow a route Reverse a routeAlter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypointGoing to an individual target Go to a waypointGo to cursor Go to a portChanging the display mode Stop follow or stop gotoCDI display BDI display BRG 234 T RNG 12.4 nm Waypoint dataCOG 230 T SOG 6.8 Kts Navigation dataTime Date 26/01/99 Time/Date DataDisplayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE TransferSetting up a track SettingClearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scaleSetting up the chartplotter System set up parametersMenu Options Factory New Default Setting Bearing mode Key beepUnits VariationTime offset LanguageSimulated SOG Simulated COGChart set up parameters Parameter Options Factory New Default Setting Plotter mode Waypoint symbolOrientation Show waypointsAnchor alarm XTE alarmChart text Screen amplifierChart boundaries Depth contours 5MDepth contours 10M Depth contours 20MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation GuidelinesSuppression ferrites Unpacking and inspecting the componentsConnections to other equipment Location Items Missing?Registering this Product Selecting the best location122 mm 4.8 Connecting to other equipment Mounting the chartplotterTrunnion yoke mounting Panel mountingD47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function ColorInitial Switch On System CheckChecking the Chartplotter Operation RayChart 420/420D Chartplotter Maintenance & fault finding MaintenanceServicing and Safety Routine checksResetting the system Two types of reset are available for the ChartplotterProblem solving Fault findingHow to contact Raytheon Marine US For accessories and partsFor product repair and service Worldwide supportHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2KRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COGRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty LimitationsFactory Service Centers United States of America
Top Page Image Contents