Raymarine 420D manual D47221

Page 79

5-6	RayChart 420/420D Chartplotter

The unit can be panel mounted, using the panel-mounting kit (accessory) available from your local Raytheon dealer.

Panel mount the unit as follows:

‰1. Check the selected location for the unit. A clear, flat area at least 175mm (7in) wide by 190mm (7½in) high, with at least 90mm (3½in) of clearance

behind the panel, is required.

2.Unpack the (optional) panel-mounting kit.

3.Using the supplied template, trace out the display unit cut-out and mark the drilling centres for the four securing holes outside of the cut-out area.

4.To provide start holes for removing the cut-out, drill four 10mm (3/8 in) holes in each opposing corner and four 6mm (1/4 in) holes for the two trunnion lug clearance slots in the cut-out area.

5.Using a suitable saw, cut along the inside edge of the cut-out line.

6.With the trunnion (yoke) and knobs removed, make sure that the unit fits in the cut-out area.

7.Drill out the four 5mm (3/16 in) securing holes as indicated on the template. It is recommended that a 1mm (1/16 in) pilot hole is drilled first.

8.Screw the studs into the vacant holes at the rear of the unit, hand tight only.

9.Place the gasket on the unit and slide the unit into the panel cut-out.

10.Secure the unit with the thumb nuts, hand tight only.

D4722_1

Image 79

Contents Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s HandbookUnited States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Display options Operating controls128 nm Trackpad and cursorFunction bar Dedicated keysDatabase lists Pop-up menusConventions used Getting startedSimulator Switching on/off Chart simulator Controlling the display Selecting the display modeTime 1234 Date 26/01/99 Using Find Ship Moving around the chartStatus Bar Chart range Changing the chart scale128 nm Using Navionics Nav-Chart cardsInserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypointsPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypointWorking with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screenErasing or renaming a route Displaying route leg and waypoint informationEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a routeFollowing routes and going to target points Reverse a route Follow a routeAlter a route Target point arrivalJoin a route Advance to a waypoint Restart Cross Track Error XTEGo to a waypoint Going to an individual targetGo to a port Go to cursorStop follow or stop goto Changing the display modeCDI display BDI display Waypoint data BRG 234 T RNG 12.4 nmNavigation data COG 230 T SOG 6.8 KtsTime/Date Data Time Date 26/01/99Displayed waypoints Transferring waypoints and routesManaging database lists WPT/ROUTE Transfer Using tracksSetting Setting up a trackClearing the current track Man Overboard MOBSmartRoute‰ Range key operates normally to change chart scale AlarmsSystem set up parameters Setting up the chartplotterMenu Options Factory New Default Setting Variation Bearing modeKey beep UnitsSimulated COG Time offsetLanguage Simulated SOGChart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol OrientationScreen amplifier Anchor alarmXTE alarm Chart textDepth contours 20M Chart boundariesDepth contours 5M Depth contours 10MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines InstallationSuppression ferrites Unpacking and inspecting the componentsConnections to other equipment Selecting the best location LocationItems Missing? Registering this Product122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mountingD47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector Function Color System Check and Initial Switch OnSystem Check Initial Switch OnChecking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and SafetyTwo types of reset are available for the Chartplotter Resetting the systemFault finding Problem solvingWorldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and serviceHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a SpecificationRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviationsRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty CertificateUnited States of America Factory Service Centers