Raymarine 420D manual Unpacking and inspecting the components, Suppression ferrites

Page 75

5-2

RayChart 420/420D Chartplotter

 

 

If a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position.

Suppression ferrites

The following illustration shows typical cable suppression ferrites fitted to Raytheon equipment. Always use the ferrites supplied by Raytheon.

Connections to other equipment

If your Raytheon equipment is to be connected to other equipment using a cable not supplied by Raytheon, a suppression ferrite MUST always be fitted to the cable close to the Raytheon unit.

5.2 Unpacking and inspecting the components

Unpack your RayChart 420 Chartplotter carefully. Retain the carton and packing materials in the event that you need to return the unit for service.

Check that you have all the correct system components. These depend on your system package:

Item

Part No.

Supplied with

 

 

 

RC420 System

E32012

 

comprising:

 

 

RC420 Chartplotter

E32014

RC420

RS112LP

E32002

RC420

 

 

 

RC420D System

E32013

 

comprising:

 

 

RC420 Chartplotter

E32014

RC420D

RS114

E32003

RC420D

 

 

 

RC420 Accessories:

 

 

Sun cover

E35004

All

Panel mounting kit

E35006

Optional

Trunnion mount kit

E35005

All

Power cable

R38024

All

GPS extension cable

E35003

Optional

 

 

 

Handbook

81162

All

Quick Reference Card

86051

All

 

 

 

Image 75
Contents Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s HandbookUnited States Warranty PrefaceEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Overview IntroductionHow this Handbook is organised Chartplotter display GeneralDisplay functions Display options Operating controls128 nm Trackpad and cursorFunction bar Dedicated keysDatabase lists Pop-up menusGetting started Conventions usedSimulator Switching on/off Chart simulator Controlling the display Selecting the display modeTime 1234 Date 26/01/99 Using Find Ship Moving around the chartStatus Bar Chart range Changing the chart scale128 nm Using Navionics Nav-Chart cardsInserting a Nav-Chart card Removing a Nav-Chart card Displaying the chart dataDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypointsPlacing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypointWorking with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screenDisplaying route leg and waypoint information Erasing or renaming a routeEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a routeFollowing routes and going to target points Reverse a route Follow a routeTarget point arrival Alter a routeJoin a route Advance to a waypoint Restart Cross Track Error XTEGo to a waypoint Going to an individual targetGo to a port Go to cursorStop follow or stop goto Changing the display modeCDI display BDI display Waypoint data BRG 234 T RNG 12.4 nmNavigation data COG 230 T SOG 6.8 KtsTime/Date Data Time Date 26/01/99Transferring waypoints and routes Displayed waypointsManaging database lists WPT/ROUTE Transfer Using tracksSetting Setting up a trackMan Overboard MOB Clearing the current trackSmartRoute‰ Range key operates normally to change chart scale AlarmsSystem set up parameters Setting up the chartplotterMenu Options Factory New Default Setting Variation Bearing modeKey beep UnitsSimulated COG Time offsetLanguage Simulated SOGChart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol OrientationScreen amplifier Anchor alarmXTE alarm Chart textDepth contours 20M Chart boundariesDepth contours 5M Depth contours 10MGPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines InstallationUnpacking and inspecting the components Suppression ferritesConnections to other equipment Selecting the best location LocationItems Missing? Registering this Product122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mountingD47221 Chartplotter connectors GPS connectorCabling POWER/NMEA connector Function Color System Check and Initial Switch OnSystem Check Initial Switch OnChecking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and SafetyTwo types of reset are available for the Chartplotter Resetting the systemFault finding Problem solvingWorldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and serviceHow to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a SpecificationRayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviationsRayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty CertificateUnited States of America Factory Service Centers