Lexicon MPX 550 manual Communications Notice

Page 3

COMMUNICATIONS NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna.

Relocate the computer with respect to the receiver.

Move the computer away from the receiver.

Plug the computer into a different outlet so that the computer and receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: "How to identify and Resolve Radio/TV Interference Problems." This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

A Harman International Company

Lexicon, Inc.

3 Oak Park

Bedford, MA 01730-1441 USA Tel 781-280-0300

Fax 781-280-0490 www.lexicon.com

Customer Support

Tel 781-280-0300

Fax 781-280-0495 (Sales)

Fax 781-280-0499 (Service)

Lexicon Part No. 070-14912 Rev 1 02/02

© 2002 Lexicon, Inc. All rights reserved.

This document should not be construed as a commitment on the part of Lexicon, Inc. The information it contains is subject to change without notice. Lexicon, Inc. assumes no responsibility for errors that may appear within this document.

Image 3
Contents Page Important Safety Instructions Communications Notice Introduction System Mode English Instrucciones DE Seguridad Italiano Importanti Norme DI Sicurezza Vii Viii US Important User Information DE Wichtige Benutzerinformation ES Información importante para el usuario FR Important Informations Utilisateur IT Importanti informazioni per l’utente PT Informações Importantes ao usuário Getting Started About the MPX Getting StartedHighlights System Front Panel OverviewInput Trim Edit PagesStore Tap/CancelPower Edit KnobsInput/OVL Indicator Front Panel DisplayInput Level Meters Tempo Routing ConfigurationBank Name Edit Knobs 1 toCord AC Input ConnectorProvides power to the unit with the supplied power Rear Panel OverviewPdif in and OUT Analog OUTPUTsAnalog INPUTs Footswitch Connecting the UnitTypical Connections to a Console Setting Audio Levels InputOutput Basic Operation Selecting and Loading Programs Basic OperationEditing Programs Adjust ParameterStoring Programs Compressor Audio TAP TAP Tempo Matching RhythmBypass Global TempoSystem Mode Parameter Settings System Mode FunctionsRestore Default Commands Parameter Settings Midi Dumps Settings if applicableClock Source ParametersOutput Level Input SourceTempo Mode Program, Global Mix Mode Program, GlobalBypass Mode Dry, Full Mute, Input Mute Program Load ModeMidi Channel Off, 1 to 16, Omni Midi Patches Enabled, DisabledMidi Clock Enabled, Disabled Operating Mode Normal, Demo, LockedMemory Protect Enabled, Disabled Auto Load Enabled, DisabledDisplay Brightness Dump System Data Midi DumpsDump User Bank Dump Current ProgramRestore Default Commands Clear User BankFactory Init Program Descriptions Single Programs Plate Plate Programs Adjust TapGATE/INV Gate/Inv Programs Adjust TapHall Hall Programs Adjust TapChamber Chamber Programs Adjust TapAmbience Ambience Programs Adjust TapRoom Room Programs Adjust TapTremolo Tremolo Programs Adjust TapRotary Rotary Programs Adjust TapChorus Chorus Programs Adjust TapFlange Flange Programs Adjust TapDetune Detune Programs Adjust TapPitch Pitch Programs Adjust TapDLY/EKO Dly/Eko Programs Adjust Tap Special FX Special FX Programs Adjust TapStereo Stage Dual Programs MSplit Dly, MSplit RvbDual Mono EFX BAL Pitch DelayFLNG-DLY Flng-Dly Programs Adjust Tap RoutingPCH-DLY Pch-Dly Programs Adjust Tap RoutingCHOR-DLY Chor-Dly Programs Adjust Tap RoutingDLY-RVB Dly-Rvb Programs Adjust Tap RoutingFLNG-RVB Flng-Rvb ProgramsTap Routing PCH-RVB Pch-Rvb Programs Adjust Tap RoutingCHOR-RVB Chor-Rvb Programs Adjust Tap RoutingMsplit DLY MSplit Dly Programs Adjust Tap RoutingMsplit RVB MSplit Rvb Programs Adjust Tap RoutingProgram Descriptions Dual Mono Dual Mono Programs Adjust Tap RoutingCmprssr Comprssr Programs Adjust TapExpLvl 0dB to 5.89dB DynamicsPeak Expansion ExpThrshCompression Gain Min, 1 to 30, Max Tape SaturationLevel Meters Saturation Off, Modern, VintageGain Reduction Meter Typical Mastering Dynamics Control AdjustmentPeak Expansion Meter Input MeterLIVE-FOH Front of House Typical Mastering Dynamics Control AdjustmentLive-FOH Programs Adjust Tap Parameter Descriptions Parameter Graphics Parameter DescriptionsParameter Descriptions Parameter Glossary Dly Fbk To 100% CmpRels To 250msecDepth DiffusionDuration 140 to 700ms DlyTapLvlDrum Dep To 100% Drum ResIntrvl HighSlope and LowSlopeHorn Dep To 100% Horn ResMstrRate To 100% Phase To 270degPreDelay 0ms to 1.198sec Mix Dry, 1 to 99%, WetResonanc Rate To 50.05Hz RvbLvlRes 1 ShapeSweep To 100ms SpeedSpeed 1 SpreadSetting Description WavformWidth Midi Operation Midi Channel Assignment Learn ModeMidi Program Banks Program Change Messages Loading ProgramsContinuous Controllers Activating Bypass or TAP FunctionsMidi Operation Midi Clock Sysex Messages Function Transmitted Recognized Remarks Midi Implementation ChartYes Appendix Appendix SpecificationsDeclaration of Conformity Index Index MPX Limited Warranty Customer Support Dry Tracks Total Time