ClearOne comm operation manual AP400 Installation ClearOne Part No July 2002 Rev

Page 2

rights reserved. No part of this document may

be reproduced in any form or by any means

without written permission from ClearOne

Communications, Inc. Printed in the United

States of America. ClearOne Communications,

Inc. reserves specific privileges. Information in

this document is subject to change without

notice.

AP400 Installation and

Operation Manual

ClearOne Part No. 800-150-001

July 2002 (Rev. 5.0)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 2

Contents AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Table of Contents IiiAppendices AP-Ware SoftwareOperation Introduction Product OverviewFeatures Technical Support Professional Services GroupSales and Customer Service ClearOne Communications EuMEA GmbHFront panel UnpackingControls and Connections Rear panel Introduction ~ Controls and ConnectionsLink Network Link busControl bus Introduction ~ G-Link Networking BusLink EC Reference bus NOMTechnical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements Hardware Setup AP400 installation diagramTo connect the AP400 Connecting the unitInstallation ~ Hardware Setup Link connections Installation ~ Networking UnitsNetworking Units To create a G-Link networkTo set the device ID Mixer modeDevice IDs Device typesEC reference To set mixer modeErrors LCD Programming Installation ~ LCD ProgrammingSwitching from one main menu category to another Menu treesAdjusting a value LCD menu treeLock panel Select presetSystem parameters Set passcodeUnit ID Mixer modeDevice ID Gate parametersGate Ratio Last Mic ModeFirst mic priority Off Attenuation Hold TimeTo determine ambient level Decay RateManual Ambient Combination ChannelsInstallation ~ LCD Programming RS-232 Inputs Installation ~ LCD Programming TelcoInput parameters EQ Status Phantom PowerHigh-Pass Filter Chairman MicInputs A-D, Telco Echo cancellerNLP adjust SubbusOutput 1-4, Output A-D, Telco Output parametersRouting parameters EC reference and PA Installation ~ LCD Programming SubbusLink X-Z buses Link reference Slave unitInputs, Outputs, ERL/TERL, and ERLE/TERLE Default MeterMeter parameters Installation ~ Worksheet 64MB RAM DescriptionAP-Ware software requirements Installing AP-Ware To install AP-WareFront Panel Controlling the volumeTo adjust the volume MutingTo mute or unmute an output Telco InterfaceTo make and disconnect a call InstructionsCustom control through DB-25 port Other telco optionsControllers Operation ~ ControllersTouch panel control Appendix a Specifications AppendicesThis warranty is void if Appendix B Warranty and ComplianceWarranty FCC Part 68 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 15 Compliance Industry Canada Compliance Safety Information RS-232 COM DCE port pinout Appendix C Connector PinoutsAppendices ~ Appendix C Connector Pinouts Control/Status port pinoutAppendices ~ Appendix D Accessories Appendix D AccessoriesAppendix E Serial Commands Accessory ClearOne Part NumberMref Command SyntaxError Codes DeviceAppendices ~ Appendix E Serial Commands Figure E.1. AP400 Serial CommandsExplanation Serial Command Parameters ExplanationsAamb Return ValuesDevice AGC CH AGCDevice AD CH= A-DBYE AmblvlBaud ChairoDfltm DecayDial Erle ERLFPP FlowFMP Microphone gating key GainExamples ExampleHold GmodeGratio HookLMO HookdLFP LVLMEQ MasterMdmode Mline MHPMinit Mtrx MmaxMpass Input Input word assignmentReturn Values OutputmixOUTPUTMIXNote =NULL Mute NLPDevice Mute CH W Device NLP CH Null NOMOffa PAAExample Preset Preset RefselTamode RingRxrd Return ValueUID TerlTerle ToutAppendix F Worksheets Figure F.1. Routing matrix worksheetAppendices ~ Appendix F Worksheets Figure F.2. Programming worksheetFigure F.3. Audio flow block diagram Index DSPIndex ~ P-Z