ClearOne comm AP400 operation manual Unpacking, Controls and Connections, Front panel

Page 8

4	Introduction ~ Unpacking

Unpacking

Ensure that the equipment shown below was received with your shipment.

ClearOne is not responsible ! for product damage incurred during shipment.

You must make claims directly with the carrier. Inspect your shipment carefully for obvious signs of damage. If the shipment appears to be damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier immediately.

Audio Products

AP400 Audio Conferencing System

Figure 1.1. Equipment

Controls and Connections

Front panel

AB C D E FG H

Figure 1.2. Front panel controls

✍	AP-Ware software provides
	AP-Ware software provides
	complete	configuration
	capabilities for the AP400.

Please refer to the AP-Ware help file for more information.

A.LCD. The two-line, 16-character-per-line LCD display is used for AP400 setup and level adjustments in conjunction with the four associated front- panel buttons [B]. Functions that can be accessed via the front-panel LCD include setup, programming, troubleshooting, and numeric audio level and gain readouts.

B.Enter/▲▼ /ESC. These buttons are used to navigate the AP400’s menu system.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 8

Contents AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Table of Contents IiiAppendices AP-Ware SoftwareOperation Introduction Product OverviewFeatures Professional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbHFront panel UnpackingControls and Connections Rear panel Introduction ~ Controls and ConnectionsLink Network Link busIntroduction ~ G-Link Networking Bus Link EC Reference busControl bus NOMTechnical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements Hardware Setup AP400 installation diagramTo connect the AP400 Connecting the unitInstallation ~ Hardware Setup Installation ~ Networking Units Networking UnitsLink connections To create a G-Link networkMixer mode Device IDsTo set the device ID Device typesEC reference To set mixer modeErrors Installation ~ LCD Programming Switching from one main menu category to anotherLCD Programming Menu treesAdjusting a value LCD menu treeSelect preset System parametersLock panel Set passcodeMixer mode Device IDUnit ID Gate parametersGate Ratio Last Mic ModeFirst mic priority Off Attenuation Hold TimeDecay Rate Manual AmbientTo determine ambient level Combination ChannelsInstallation ~ LCD Programming RS-232 Inputs Installation ~ LCD Programming TelcoInput parameters Phantom Power High-Pass FilterEQ Status Chairman MicEcho canceller NLP adjustInputs A-D, Telco SubbusOutput 1-4, Output A-D, Telco Output parametersRouting parameters EC reference and PA Installation ~ LCD Programming SubbusLink X-Z buses Link reference Slave unitInputs, Outputs, ERL/TERL, and ERLE/TERLE Default MeterMeter parameters Installation ~ Worksheet 64MB RAM DescriptionAP-Ware software requirements Installing AP-Ware To install AP-WareControlling the volume To adjust the volumeFront Panel MutingTelco Interface To make and disconnect a callTo mute or unmute an output InstructionsOther telco options ControllersCustom control through DB-25 port Operation ~ ControllersTouch panel control Appendix a Specifications AppendicesThis warranty is void if Appendix B Warranty and ComplianceWarranty FCC Part 68 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 15 Compliance Industry Canada Compliance Safety Information Appendix C Connector Pinouts Appendices ~ Appendix C Connector PinoutsRS-232 COM DCE port pinout Control/Status port pinoutAppendix D Accessories Appendix E Serial CommandsAppendices ~ Appendix D Accessories Accessory ClearOne Part NumberCommand Syntax Error CodesMref DeviceAppendices ~ Appendix E Serial Commands Figure E.1. AP400 Serial CommandsSerial Command Parameters Explanations AambExplanation Return ValuesAGC Device ADDevice AGC CH CH= A-DAmblvl BaudBYE ChairoDfltm DecayDial Erle ERLFPP FlowFMP Gain ExamplesMicrophone gating key ExampleGmode GratioHold HookHookd LFPLMO LVLMEQ MasterMdmode Mline MHPMinit Mmax MpassMtrx Input Input word assignmentReturn Values OutputmixOUTPUTMIXNote =NULL Mute NLPDevice Mute CH W Device NLP CH NOM OffaNull PAAExample Preset Preset RefselRing RxrdTamode Return ValueTerl TerleUID ToutAppendix F Worksheets Figure F.1. Routing matrix worksheetAppendices ~ Appendix F Worksheets Figure F.2. Programming worksheetFigure F.3. Audio flow block diagram Index DSPIndex ~ P-Z