ClearOne comm AP400 operation manual Flow, Fmp, Fpp

Page 55

Appendices ~ Appendix E: Serial Commands

FLOW

This command selects or reports whether hardware flow control is enable or disabled for the AP400. Hardware flow control is implemented using RTS and CTS.

[DEVICE] FLOW <X>

Explanation

<X>

X=0	Sets flow control to OFF
X=1	Sets flow control to ON
X=Null	Parameter to return the current mode

Return Values

The command will return the updated condition (On=1, Off=0) of the AP400 in the same format as the command.

FMP

This command selects or returns the current status of the first microphone priority mode for the AP400.

[DEVICE] FMP <X>

Explanation

<X>

X=0	Parameter to select first microphone priority
	mode to OFF
X=1	Parameter to select first microphone priority
	mode to ON
X=Null	Parameter to return the current mode

Return Values

The command will return the updated condition (On=1, Off=0) of first mic priority mode in the same format as the command.

51

FPP

This command sets and reports the current passcode setting for the AP400.

[DEVICE] FPP <XXXXX>

Explanation

<XXXXX>

X=1	▲ button
X=2	Enter button
X=3	Esc button
X=4	▼ button
X=5	Meter button
X=6	Input button
X=7	System button
X=8	Output button
X=9	Routing button
X=Null	Parameter to return current passcode

Return Values

The command returns the current or updated condition of the front panel passcode.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 55

Contents AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Iii Table of ContentsOperation AP-Ware SoftwareAppendices Product Overview IntroductionFeatures ClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportControls and Connections UnpackingFront panel Introduction ~ Controls and Connections Rear panelLink bus Link NetworkNOM Introduction ~ G-Link Networking BusLink EC Reference bus Control busTechnical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements AP400 installation diagram Hardware SetupInstallation ~ Hardware Setup Connecting the unitTo connect the AP400 To create a G-Link network Installation ~ Networking UnitsNetworking Units Link connectionsDevice types Mixer modeDevice IDs To set the device IDErrors To set mixer modeEC reference Menu trees Installation ~ LCD ProgrammingSwitching from one main menu category to another LCD ProgrammingLCD menu tree Adjusting a valueSet passcode Select presetSystem parameters Lock panelGate parameters Mixer modeDevice ID Unit IDFirst mic priority Last Mic ModeGate Ratio Hold Time Off AttenuationCombination Channels Decay RateManual Ambient To determine ambient levelInstallation ~ LCD Programming RS-232 Input parameters Installation ~ LCD Programming TelcoInputs Chairman Mic Phantom PowerHigh-Pass Filter EQ StatusSubbus Echo cancellerNLP adjust Inputs A-D, TelcoRouting parameters Output parametersOutput 1-4, Output A-D, Telco Link X-Z buses Installation ~ LCD Programming SubbusEC reference and PA Slave unit Link referenceMeter parameters Default MeterInputs, Outputs, ERL/TERL, and ERLE/TERLE Installation ~ Worksheet AP-Ware software requirements Description64MB RAM To install AP-Ware Installing AP-WareMuting Controlling the volumeTo adjust the volume Front PanelInstructions Telco InterfaceTo make and disconnect a call To mute or unmute an outputOperation ~ Controllers Other telco optionsControllers Custom control through DB-25 portTouch panel control Appendices Appendix a SpecificationsWarranty Appendix B Warranty and ComplianceThis warranty is void if FCC Part 15 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 68 Compliance Industry Canada Compliance Safety Information Control/Status port pinout Appendix C Connector PinoutsAppendices ~ Appendix C Connector Pinouts RS-232 COM DCE port pinoutAccessory ClearOne Part Number Appendix D AccessoriesAppendix E Serial Commands Appendices ~ Appendix D AccessoriesDevice Command SyntaxError Codes MrefFigure E.1. AP400 Serial Commands Appendices ~ Appendix E Serial CommandsReturn Values Serial Command Parameters ExplanationsAamb ExplanationCH= A-D AGCDevice AD Device AGC CHChairo AmblvlBaud BYEDial DecayDfltm ERL ErleFMP FlowFPP Example GainExamples Microphone gating keyHook GmodeGratio HoldLVL HookdLFP LMOMdmode MasterMEQ Minit MHPMline Input Input word assignment MmaxMpass MtrxOUTPUTMIXNote OutputmixReturn Values Device Mute CH W Device NLP CH Mute NLP=NULL PAA NOMOffa NullExample Preset Refsel PresetReturn Value RingRxrd TamodeTout TerlTerle UIDFigure F.1. Routing matrix worksheet Appendix F WorksheetsFigure F.2. Programming worksheet Appendices ~ Appendix F WorksheetsFigure F.3. Audio flow block diagram DSP IndexIndex ~ P-Z