ClearOne comm Appendices ~ Appendix E Serial Commands, Figure E.1. AP400 Serial Commands

Page 49

Appendices ~ Appendix E: Serial Commands

The command string will then be explained (where necessary), followed by the

returned values and (where necessary) an example.

Figure E.1. AP400 Serial Commands

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 49

Contents AP400 Audio Conferencing System AP400 Installation ClearOne Part No July 2002 Rev Iii Table of ContentsOperation AP-Ware SoftwareAppendices Product Overview IntroductionFeatures Sales and Customer Service Professional Services GroupTechnical Support ClearOne Communications EuMEA GmbHControls and Connections UnpackingFront panel Introduction ~ Controls and Connections Rear panelLink bus Link NetworkLink EC Reference bus Introduction ~ G-Link Networking BusControl bus NOMTechnical Services Group ~ 1-800-283-5936 USA ~ Equipment Requirements AP400 installation diagram Hardware SetupInstallation ~ Hardware Setup Connecting the unitTo connect the AP400 Networking Units Installation ~ Networking UnitsLink connections To create a G-Link networkDevice IDs Mixer modeTo set the device ID Device typesErrors To set mixer modeEC reference Switching from one main menu category to another Installation ~ LCD ProgrammingLCD Programming Menu treesLCD menu tree Adjusting a valueSystem parameters Select presetLock panel Set passcodeDevice ID Mixer modeUnit ID Gate parametersFirst mic priority Last Mic ModeGate Ratio Hold Time Off AttenuationManual Ambient Decay RateTo determine ambient level Combination ChannelsInstallation ~ LCD Programming RS-232 Input parameters Installation ~ LCD Programming TelcoInputs High-Pass Filter Phantom PowerEQ Status Chairman MicNLP adjust Echo cancellerInputs A-D, Telco SubbusRouting parameters Output parametersOutput 1-4, Output A-D, Telco Link X-Z buses Installation ~ LCD Programming SubbusEC reference and PA Slave unit Link referenceMeter parameters Default MeterInputs, Outputs, ERL/TERL, and ERLE/TERLE Installation ~ Worksheet AP-Ware software requirements Description64MB RAM To install AP-Ware Installing AP-WareTo adjust the volume Controlling the volumeFront Panel MutingTo make and disconnect a call Telco InterfaceTo mute or unmute an output InstructionsControllers Other telco optionsCustom control through DB-25 port Operation ~ ControllersTouch panel control Appendices Appendix a SpecificationsWarranty Appendix B Warranty and ComplianceThis warranty is void if FCC Part 15 Compliance Appendices ~ Appendix B Warranty and ComplianceFCC Part 68 Compliance Industry Canada Compliance Safety Information Appendices ~ Appendix C Connector Pinouts Appendix C Connector PinoutsRS-232 COM DCE port pinout Control/Status port pinoutAppendix E Serial Commands Appendix D AccessoriesAppendices ~ Appendix D Accessories Accessory ClearOne Part NumberError Codes Command SyntaxMref DeviceFigure E.1. AP400 Serial Commands Appendices ~ Appendix E Serial CommandsAamb Serial Command Parameters ExplanationsExplanation Return ValuesDevice AD AGCDevice AGC CH CH= A-DBaud AmblvlBYE ChairoDial DecayDfltm ERL ErleFMP FlowFPP Examples GainMicrophone gating key ExampleGratio GmodeHold HookLFP HookdLMO LVLMdmode MasterMEQ Minit MHPMline Mpass MmaxMtrx Input Input word assignmentOUTPUTMIXNote OutputmixReturn Values Device Mute CH W Device NLP CH Mute NLP=NULL Offa NOMNull PAAExample Preset Refsel PresetRxrd RingTamode Return ValueTerle TerlUID ToutFigure F.1. Routing matrix worksheet Appendix F WorksheetsFigure F.2. Programming worksheet Appendices ~ Appendix F WorksheetsFigure F.3. Audio flow block diagram DSP IndexIndex ~ P-Z