Yamaha CLP-F01 owner manual F6. Metronome Volume, Sub-mode Midi Transmit Channel Selection

Page 47

F6. Metronome Volume

You can change the volume of the metronome sound.

Use this function to adjust the metronome vol- ume.

1. Engage Function mode and select

 

.

2.Use the [–/NO] and [+/YES] buttons to set the metronome volume as required.

Setting range: 1 – 20

Normal setting: 10

TIP

SHORTCUT:

 

You can jump directly to the metronome functions

by

pressing the [TEMPO/FUNCTION#] button while holding the METRONOME [START/STOP] button.

To exit Function mode, you still need to press the [TEMPO/ FUNCTION#] button so that the TEMPO indicator lights up.

F7.

Preset Song Part Cancel Volume

This function sets the volume at which a “can- celed” part is played during preset song play- back. Adjust the part volume to a comfortable level and use the “canceled” part as a guide with which to play along.

1. Engage Function mode and select

 

.

2.Use the [–/NO] and [+/YES] buttons to set the volume as required.

Setting range: 0 – 20

Normal setting: 5

F8. MIDI Functions

You can make detailed adjustments to MIDI settings.

For more information about MIDI, see the “About MIDI” section (page 51).

TIP

The HOST SELECT switch on the bottom surface must be set to “MIDI” to enable the MIDI connectors. When you use the TO HOST connector, set the HOST SELECT switch to the appropriate position for the type of computer you are using (pages 51–57). In this situation, all MIDI settings described below will affect the MIDI signal in and out of the TO HOST connector.

1.Engage Function mode and select .

2.Press the [+/YES] button to engage the MIDI function’s sub-mode, then use the [TEMPO/ FUNCTION# ▼ ▲] buttons to select the desired sub-mode.

Press the [–/NO] or [+/YES] button to set a selected parameter.

Sub-mode

MIDI Transmit Channel Selection

In any MIDI control setup, the MIDI channels of the transmitting and receiving equipment must be matched for proper data transfer.

This parameter enables you to specify the channel on which the Clavinova transmits MIDI data.

Setting range: 1 – 16, OFF (not transmitted)

Normal setting: 1

NOTE

In Dual mode, Voice 1 data is transmitted on its specified channel. In Split mode, right voice data is transmitted on its specified channel. In Dual mode, Voice 2 data is transmitted on the next greater channel number relative to the specified channel. In Split mode, left voice data is transmitted on the next greater channel number relative to the specified chan- nel. In either mode, no data is transmitted if the transmit channel is set to “OFF”.

NOTE

Demo/preset song data and recorder playback data are not transmitted via MIDI.

ENGLISH

CLP-F01Detailed Settings – [FUNCTION] 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents CLP-F01 Special Message Section Precautions Connections Appendix TrademarksIntroduction ReferenceTable of Contents Application Index Transporting AccessoriesTuning Bench may be included or optional, depending on your localeTranspose FeaturesTo close the key cover Before Using the ClavinovaKey Cover To open the key coverTo replace the music rest Music RestTo position the music rest for use Power indicator Turning the Power OnConnect the power cord Turn the power onUsing the Speaker Switch Setting the VolumeUsing Headphones option Memo Panel Controls and Terminals Clavinova’s various functionsTop panel ConnectorsPanel Controls and Terminals Display Listening to the Demonstration Tunes Stop playback Listening to 50 Piano Preset SongsEngage Preset Song mode Play any of the 50 preset songsStart playback and playing Exit from Preset Song modeHow to use the practice functions Turn off the playback part you wish to practiceLeft Pedal Start/Stop Will appear on the dis Repeat for 50 Preset SongsDamper Right Pedal Using the PedalsSelecting & Playing Voices Selecting VoicesSoft Left Pedal Normal settingSostenuto Center Pedal Depth 0 no effect Depth 20 maximum effect depth Adjusting Reverb DepthAdjusting Effect Depth Depth 0 no effectTouch Sensitivity Touch Changing the volume when Fixed is selectedTranspose Transposition TransposeExit Dual mode and return to normal play mode Combining Two Voices Dual modeEngage Dual mode Split Engage Split modeSelect a voice for the left hand Exit Split mode and return to normal play modePress the Split button again so that its indicator goes out Select a voice for the right handStart the metronome Using the MetronomeAdjusting the tempo Adjusting the time signatureRecording vs. Saving Make all the initial settingsRecording Your Performance Select a song for recordingStop recording Engage Record modeSelect the record track Start recordingRecording to Track Re-recording TrackEntire Song Individual TracksVoice selection Press the REC button to exit Record mode You can change the following initial settingsChange the settings via the panel controls Select the desired song Midi connectorsPlaying Back Recorded Songs Playing Back a SongSynchro Useful Playback FunctionsTurning track playback on and off Assigning the START/STOP function to the left pedalParameter List Detailed Settings FunctionUse the -/NO +/YES buttons Basic Procedure in Function ModeEngage Function mode Select a functionOperation Example 2 F3.1 Dual Balance Do the following when you finish using the func- tionOperation Example 1 F1. Fine tuning of the pitch Hz Hertz Setting rangeAbout Each Function Display ValueMeanTone EqualPureMajor/PureMinor PythagoreanVoice 1 Octave Shift Voice 2 Octave Shift ResetSub-mode Dual Balance Dual DetuneRight Voice Effect Depth Left Voice Effect Depth Sub-mode Split PointSplit Balance Right Voice Octave Shift Left Voice Octave ShiftSustain Sample Depth Sub-mode Left Pedal ModeKeyoff Sample Volume Soft Pedal Effect DepthSub-mode Midi Transmit Channel Selection F6. Metronome VolumeProgram Change ON/OFF Setting range ON/OFF Normal setting onMidi Receive Channel Selection Local Control ON/OFFBulk Data Dump ProcedureMidi Transmit Transpose Panel/Status TransmitDescription of sub-modes Voice Sub-mode Voice Midi Tuning OthersFactory Preset Recall Setting range ON/OFF Normal setting OFF all groupsMidi cables Midi connectorsTo Host connector About MidiConnections ConnectorsAUX in L/L+R jack or AUX OUT L/L+R jack AUX in R, L/L+R jacksOn the power to the computer first, then to the Clavinova Connecting a Personal ComputerConnection Type of serial cables and connection pin assignmentsConnection Clavinova Host Select switch settingSet the Clavinova Host Select switch to Midi Computer Problem Possible Cause and Solution TroubleshootingInsert the rear panel center Keyboard Stand AssemblyRemoving the panels Attach the fall-prevention bracket Install the rear panels left and rightVoltage Selector Fasten the rear panels securelyCheck the connection After completing the assembly, please check the followingReview the assembly procedure and correct any errors Move the Clavinova to an appropriate locationVoice Name Stereo Touch Dynamic Key-Off Voice Descriptions Preset Voice ListWood Bass Voice Name Piano Voice Demo Demo Song ListPiano Voice Demo Description Voice Name Title ComposerIndex Start/Stop playback Practicing a One-Hand Part Using 50 Preset Songs......20Soft Pedal 16, 24 16, 29Appendix Function Backup GroupFunction number Default Backup Group CLP-F01Appendix Panel Data Transmit Panel Data ContentsMidi Master Volume Data format F0H 7EH XnH 09H 01H F7H General Midi Mode OnMidi Parameter Change table Multi Part Effect Midi MapMidi Parameter Change table Effect Midi Implementation Chart ON/OFF Memo Memo Please Keep this Manual FCC Information U.S.A North America Clavinova Web site English only Yamaha Manual Library
Top Page Image Contents