Yamaha CLP-F01 Midi Transmit Transpose, Panel/Status Transmit, Procedure, Bulk Data Dump

Page 49

MIDI Transmit Transpose

This function allows the MIDI note data transmitted by the CLP-F01 to be transposed up or down in semitone increments by up to plus or minus 12 semitones. The pitch of the CLP-F01 itself is not affected.

Setting range: -12 – 0 – 12 (in semitones)

Normal setting: 0

Panel/Status Transmit

This function causes all the current CLP-F01 panel set- tings (selected voice, etc.) to be transmitted via the MIDI OUT terminal. This is particularly useful if you will be recording performances to a MIDI sequence recorder, such as the Yamaha MIDI Data Filer MDF3, which will be used to control the CLP-F01 on playback. By trans- mitting the CLP-F01 panel settings and recording them on the MIDI sequence recorder prior to the actual per- formance data, the CLP-F01 will be automatically restored to the same settings when the performance is played back.

TERMINOLOGY

Setup Data:

Data that contains a set of panel settings for the Clavinova.

Procedure

1.Set up the panel controls as desired.

2.Connect the Clavinova to a sequencer via MIDI, and set up the sequencer so it can receive the setup data.

3.Engage Function mode and select .

4.Press the [+/YES] button to transmit the panel/status data.

will appear on the LED display when the data has been successfully transmitted.

TIP

See page 70 for a list of the “Panel Data Contents” transmit- ted by this function.

TIP

Receiving the transmitted data:

1.Connect the Clavinova via MIDI to the device to which the setup data was transmitted previously.

2.Start sending the setup data from the device.

The Clavinova automatically receives the setup data, which will be reflected in the panel settings.

(For the data to be accepted, the Clavinova that receives the setup data should be the same model as the one that trans- mitted the setup data to the sequencer.)

TIP

For more information on transmitting and receiving setup data via MIDI, refer to the owner’s manual for the connected MIDI device.

Bulk Data Dump

You can save current song data on the Clavinova as MIDI bulk data by transferring it to a connected MIDI data filer (such as an MDF3) or a sequencer. To play back the saved song data, send the bulk data back from the storage device to the Clavinova and follow the usual playback procedure.

TERMINOLOGY

bulk data:

A complete set or extended sequence of data.

Procedure

1.Record your performance on the Clavinova.

2.Connect the Clavinova to MDF3, a MIDI data filer via MIDI, and set up the MDF3 so it will receive bulk data.

3.Engage Function mode and select .

4.Press the [+/YES] button to begin bulk transmission.

will appear on the LED display when the data has been successfully transmitted.

NOTE

No MIDI note/panel data transmission or data reception occurs during a bulk data dump transmit operation.

TIP

Receiving (returning) the transmitted data:

1.Connect the CLP-F01 via MIDI to the device to which the data was previously transmitted.

2.Start sending the data from the device.

The CLP-F01 automatically receives the data from the unit. (At this time, any data previously stored in the Clavinova will be erased.)

Then, follow the usual playback procedure.

(For the data to be accepted, the Clavinova that receives the data should be the same model as the one from which the data was once transmitted to the MIDI data filer.)

NOTE

The reload operation cannot be executed when Demo/Preset Song mode or the user song recorder is in operation, or when Function mode is engaged.

TIP

For more information on transmitting and receiving bulk data via MIDI, refer to the owner’s manual for the connected MIDI device.

ENGLISH

CLP-F01Detailed Settings – [FUNCTION] 49

Page 48 Page 50
Image 49
Page 48 Page 50
Contents CLP-F01 Special Message Section Precautions Connections Introduction TrademarksReference AppendixTable of Contents Application Index Tuning AccessoriesBench may be included or optional, depending on your locale TransportingTranspose FeaturesKey Cover Before Using the ClavinovaTo open the key cover To close the key coverTo position the music rest for use Music RestTo replace the music rest Connect the power cord Turning the Power OnTurn the power on Power indicatorUsing Headphones option Setting the VolumeUsing the Speaker Switch Memo Panel Controls and Terminals Clavinova’s various functionsPanel Controls and Terminals ConnectorsTop panel Display Listening to the Demonstration Tunes Engage Preset Song mode Listening to 50 Piano Preset SongsPlay any of the 50 preset songs Stop playbackHow to use the practice functions Exit from Preset Song modeTurn off the playback part you wish to practice Start playback and playingLeft Pedal Start/Stop Will appear on the dis Repeat for 50 Preset SongsSelecting & Playing Voices Using the PedalsSelecting Voices Damper Right PedalSostenuto Center Pedal Normal settingSoft Left Pedal Adjusting Effect Depth Adjusting Reverb DepthDepth 0 no effect Depth 0 no effect Depth 20 maximum effect depthTouch Sensitivity Touch Changing the volume when Fixed is selectedTranspose Transposition TransposeEngage Dual mode Combining Two Voices Dual modeExit Dual mode and return to normal play mode Split Engage Split modePress the Split button again so that its indicator goes out Exit Split mode and return to normal play modeSelect a voice for the right hand Select a voice for the left handAdjusting the tempo Using the MetronomeAdjusting the time signature Start the metronomeRecording Your Performance Make all the initial settingsSelect a song for recording Recording vs. SavingSelect the record track Engage Record modeStart recording Stop recordingRecording to Track Re-recording TrackVoice selection Individual TracksEntire Song Change the settings via the panel controls You can change the following initial settingsPress the REC button to exit Record mode Playing Back Recorded Songs Midi connectorsPlaying Back a Song Select the desired songTurning track playback on and off Useful Playback FunctionsAssigning the START/STOP function to the left pedal SynchroParameter List Detailed Settings FunctionEngage Function mode Basic Procedure in Function ModeSelect a function Use the -/NO +/YES buttonsOperation Example 1 F1. Fine tuning of the pitch Do the following when you finish using the func- tionOperation Example 2 F3.1 Dual Balance About Each Function Setting rangeDisplay Value Hz HertzPureMajor/PureMinor EqualPythagorean MeanToneSub-mode Dual Balance ResetDual Detune Voice 1 Octave Shift Voice 2 Octave ShiftSplit Balance Sub-mode Split PointRight Voice Octave Shift Left Voice Octave Shift Right Voice Effect Depth Left Voice Effect DepthKeyoff Sample Volume Sub-mode Left Pedal ModeSoft Pedal Effect Depth Sustain Sample DepthSub-mode Midi Transmit Channel Selection F6. Metronome VolumeMidi Receive Channel Selection Setting range ON/OFF Normal setting onLocal Control ON/OFF Program Change ON/OFFMidi Transmit Transpose ProcedurePanel/Status Transmit Bulk Data DumpFactory Preset Recall Sub-mode Voice Midi Tuning OthersSetting range ON/OFF Normal setting OFF all groups Description of sub-modes VoiceTo Host connector Midi connectorsAbout Midi Midi cablesConnections ConnectorsAUX in L/L+R jack or AUX OUT L/L+R jack AUX in R, L/L+R jacksOn the power to the computer first, then to the Clavinova Connecting a Personal ComputerConnection Type of serial cables and connection pin assignmentsSet the Clavinova Host Select switch to Midi Clavinova Host Select switch settingConnection Computer Problem Possible Cause and Solution TroubleshootingRemoving the panels Keyboard Stand AssemblyInsert the rear panel center Voltage Selector Install the rear panels left and rightFasten the rear panels securely Attach the fall-prevention bracketReview the assembly procedure and correct any errors After completing the assembly, please check the followingMove the Clavinova to an appropriate location Check the connectionVoice Name Stereo Touch Dynamic Key-Off Voice Descriptions Preset Voice ListWood Bass Piano Voice Demo Description Demo Song ListVoice Name Title Composer Voice Name Piano Voice DemoIndex Soft Pedal 16, 24 Practicing a One-Hand Part Using 50 Preset Songs......2016, 29 Start/Stop playbackAppendix Function number Default Backup Group Backup GroupFunction CLP-F01Appendix Midi Master Volume Panel Data ContentsPanel Data Transmit Data format F0H 7EH XnH 09H 01H F7H General Midi Mode OnMidi Parameter Change table Effect Effect Midi MapMidi Parameter Change table Multi Part Midi Implementation Chart ON/OFF Memo Memo Please Keep this Manual FCC Information U.S.A North America Clavinova Web site English only Yamaha Manual Library
Top Page Image Contents